Cisco 3631 Spezifikationen PDF herunterladen (Seite 125)

3-63

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

OL-1957-03

Chapter 3 Configuring with the Command-Line Interface

Configuring 1-Port G.SHDSL WAN Interface Card

• To view the status of an ATM interface, use the show interface atm command. Make sure that the

ATM slot/port and the line protocol are up, as shown in the following examples:

Router# show interface atm 1/0

ATM1/0 is up, line protocol is up

Hardware is DSLSAR (with Globespan G.SHDSL Module)

MTU 4470 bytes, sub MTU 4470, BW 800 Kbit, DLY 2560 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ATM, loopback not set

Keepalive not supported

Encapsulation(s):AAL5 AAL2, PVC mode

24 maximum active VCs, 256 VCs per VP, 2 current VCCs

VC idle disconnect time:300 seconds

Last input never, output 00:00:01, output hang never

Last clearing of "show interface" counters 03:16:00

Queueing strategy:fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

30 second input rate 0 bits/sec, 0 packets/sec

30 second output rate 0 bits/sec, 0 packets/sec

2527 packets input, 57116 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

10798 packets output, 892801 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

Router# show atm vc

VCD / Peak Avg/Min Burst

Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts

1/0.3 2 9 36 PVC MUX UBR 800 UP

1/0.2 1 9 37 PVC SNAP UBR 800 UP

Router# show controllers atm 1/0

Interface ATM1/0 is up

Hardware is DSLSAR (with Globespan G.SHDSL Module)

IDB: 62586758 Instance:6258E054 reg_dslsar:3C810000 wic_regs:3C810080

PHY Inst:62588490 Ser0Inst:62573074 Ser1Inst: 6257CBD8 us_bwidth:800

Slot: 1 Unit: 1 Subunit: 0 pkt Size:4496

VCperVP:256 max_vp: 256 max_vc: 65536 total vc:2

rct_size:65536 vpivcibit:16 connTblVCI:8 vpi_bits:8

vpvc_sel:3 enabled: 0 throttled:0

WIC Register Value Notes

--------------- ---------- ----------

FPGA Dev ID (LB) 0x44 'D'

FPGA Dev ID (UB) 0x53 'S'

FPGA Revision 0x99

WIC Config Reg 0x45 WIC / VIC select = WIC;

CTRLE addr bit 8 = 1;

OK LED on;

LOOPBACK LED off;

CD LED on;

WIC Config Reg2 0x07 Gen bus error on bad ADSL access

Int 0 Enable Reg 0x03 ADSL normal interrupt enabled

ADSL error interrupt enabled

• To view the status of the G.SHDSL modem, use the show dsl interface atm command. If the line

is down, the following statement appears: Line is not active. Some of the values may not be accurate.

You can also verify whether the equipment type and operating mode configuration are correct for

your application.

1 2 ... 120 121 122 123 124 125 126 127 128 129 130 ... 197 198

Kommentare zu diesen Handbüchern

Keine Kommentare

Cisco 3631 Spezifikationen Seite 125

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Cisco 3631