Cisco 3631 Spezifikationen Seite 136
- Seite / 198
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4-8
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 4 Configuring Voice-over-IP
Router SLC Configuration
hostname saltlake
!Configure pots dial-peer 1
dial-peer voice 1 pots
destination-pattern +569....
port 1/0/0
!Configure pots dial-peer 2
dial-peer voice 2 pots
destination-pattern +569....
port 1/0/1
!Configure voip dial-peer 3
dial-peer voice 3 voip
destination-pattern +527....
session target ipv4:172.16.1.123
!Configure the E&M interface
voice-port 1/0/0
signal immediate
operation 4-wire
type 2
voice-port 1/0/0
signal immediate
operation 4-wire
type 2
!Configure the serial interface
interface serial 0/0
description serial interface type dte
ip address 172.16.65.182
no shutdown
Note PBXs should be configured to pass all DTMF signals to the router. Cisco recommends that you do
not configure “store-and-forward” tone.
Note If you change the gain or the telephony port, make sure that the telephony port still accepts DTMF
signals.
PSTN Gateway Access Using FXO Connection
The following example shows how to configure VoIP to link users with the PSTN gateway using an FXO
connection.
In this example, users connected to Router SJ in San Jose, California can reach PSTN users in Salt Lake
City, Utah via Router SLC. Router SLC in Salt Lake City is connected directly to the PSTN through an
FXO interface.
Figure 4-3 illustrates the topology of this connection example.
- Software Configuration Guide 1
- CONTENTS 3
- A Configuration Examples A-1 8
- C Using the ROM Monitor C-1 9
- Contents 10
- OL-1957-03 10
- Objectives 11
- Audience 11
- Organization 12
- Document Conventions 12
- Additional Information 13
- Obtaining Documentation 16
- Documentation CD-ROM 17
- Ordering Documentation 17
- Documentation Feedback 17
- Cisco.com 18
- Technical Assistance Center 18
- Cisco IOS Software Basics 21
- Slot 0Slot 1 Power supply 25
- W1Slot 2 W0 26
- Console/AUX 26
- FastEthernet 0/0 26
- Slot W1 Slot W0 28
- Getting Help 33
- Understanding Command Modes 34
- Before Starting Your Router 37
- Configuring Global Parameters 38
- Frame Relay Encapsulation 44
- LAPB Encapsulation 44
- X.25 Encapsulation 45
- ATM-DXI Encapsulation 45
- SMDS Encapsulation 45
- Synchronous Configuration 46
- Asynchronous Configuration 48
- PPP Encapsulation 50
- ISDN BRI Line Configuration 51
- For data only 52
- For voice and data 52
- E1/T1 ISDN PRI Configuration 54
- T1 Channelized Mode 57
- Switched Mode 59
- Dedicated Mode 59
- Completing the Configuration 60
- • Power on the router 71
- Configuring ISDN BRI Lines 74
- Configuring T1 Interfaces 77
- Configuring E1 Interfaces 78
- Configuring Codec Complexity 80
- Default Configuration 81
- Configuring ATM Interfaces 82
- Configuring PVCs 83
- Configuring SVCs 84
- Configuring the IMA Interface 87
- Benefits 92
- Verifying ATM Configuration 94
- Serial Communication Channels 97
- Asynchronous Craft Port 98
- Serial Data Channel 98
- Configuring the AIC 100
- Accessing the AIC 102
- Configuring Alarms 103
- Verifying the IP Address 105
- Troubleshooting Tips 107
- Software Upgrade 107
- Configuration Examples 108
- Configuration Tasks 109
- Cisco 3600 Series Routers 111
- Cisco 3640 Router 112
- Prerequisites 113
- Configure the LAN Interface 117
- Configuration Example 120
- Restrictions 122
- Verifying ATM Configuration 124
- Saving Configuration Changes 127
- Where to Go Next 127
- Configuring Voice-over-IP 129
- Router SJ Configuration 135
- Router SLC Configuration 136
- • IMA-8T1 in 146
- • NM-4A/S 146
- • WIC-2A/S 146
- • WIC-1DSU-56k4 146
- With an Unnumbered IP Address 160
- Discrete Alarm 162
- Modem Calls 163
- Formatting Procedures 171
- File and Directory Operations 174
- Display File Content 176
- Copy Files 177
- Rename a File 179
- Create a New Directory 180
- Remove a Directory 181
- Using the ROM Monitor 183
- ROM Monitor Commands 184
- Command Descriptions 185
- Debugging Commands 187
- Using the xmodem Command 190
- Using the tftpdnld Command 190
- Entering the ROM Monitor Mode 192
- Numerics 193
Verwandte Produkte und Handbücher für Vernetzung Cisco 3631
Vernetzung Cisco 2650 - 2650 Router Spezifikationen
(266 Seiten)
(266 Seiten)
Vernetzung Cisco SRW224 Bedienungsanleitung
(5 Seiten)
(5 Seiten)
Vernetzung Cisco ASR1004-10G-SHA/K9 - ASR 1004 Sec+HA Bundle Router Bedienungsanleitung
(105 Seiten)
(105 Seiten)
Vernetzung Cisco 3800 Series Spezifikationen
(40 Seiten)
(40 Seiten)
Vernetzung Cisco 1802 Spezifikationen
(198 Seiten)
(198 Seiten)
Vernetzung Cisco SOHO 71 Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Vernetzung Cisco WS-C2950ST-24-LRE - Syst. 24PORT 2950-BASED LONG REACH Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Vernetzung Cisco DPC3825 Bedienungsanleitung
(109 Seiten)
(109 Seiten)
Vernetzung Cisco EPC3825 Bedienungsanleitung
(35 Seiten)
(35 Seiten)
Vernetzung Cisco SRW208MP Bedienungsanleitung
(14 Seiten)
(14 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.108 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern