Cisco 3631 Spezifikationen Seite 105
- Seite / 198
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
3-43
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 3 Configuring with the Command-Line Interface
Configuring the NM-AIC-64, Contact Closure Network Module
Programming the Discrete Contact Points
The discrete alarms do not require as much programming as the analog alarms. The AIC CLI commands
available are the following:
Verifying the IP Address
To verify that the correct AIC IP address and IP route was entered, use the show run command. Below
are samples of before-configuration and after-configuration show run command outputs:
interface Serial5/0
ip unnumbered FastEthernet0/0
!
ip route 10.2.130.102 255.255.255.255 Serial5/0
!
alarm-interface 5
ip address 10.2.130.102
********Before Configuration show run Output*******
version 12.1
no service single-slot-reload-enable
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname uut2-3660
!
logging rate-limit console 10 except errors
!
ip subnet-zero
!
!
no ip finger
no ip domain-lookup
!
call rsvp-sync
cns event-service server
!
!
interface FastEthernet0/0
ip address 10.2.130.2 255.255.0.0
duplex auto
speed auto
no cdp enable
Command Description
no Reversal option
exit Exits current mode
description Sets the description. If no is set, then the description
is not required.
normally Sets the alarm’s normal state to closed. If the no
option is used, the normal state is set to open. This
command applies only to points 1 - 56.
level Sets the alarm’s level to the specified level.
- Software Configuration Guide 1
- CONTENTS 3
- A Configuration Examples A-1 8
- C Using the ROM Monitor C-1 9
- Contents 10
- OL-1957-03 10
- Objectives 11
- Audience 11
- Organization 12
- Document Conventions 12
- Additional Information 13
- Obtaining Documentation 16
- Documentation CD-ROM 17
- Ordering Documentation 17
- Documentation Feedback 17
- Cisco.com 18
- Technical Assistance Center 18
- Cisco IOS Software Basics 21
- Slot 0Slot 1 Power supply 25
- W1Slot 2 W0 26
- Console/AUX 26
- FastEthernet 0/0 26
- Slot W1 Slot W0 28
- Getting Help 33
- Understanding Command Modes 34
- Before Starting Your Router 37
- Configuring Global Parameters 38
- Frame Relay Encapsulation 44
- LAPB Encapsulation 44
- X.25 Encapsulation 45
- ATM-DXI Encapsulation 45
- SMDS Encapsulation 45
- Synchronous Configuration 46
- Asynchronous Configuration 48
- PPP Encapsulation 50
- ISDN BRI Line Configuration 51
- For data only 52
- For voice and data 52
- E1/T1 ISDN PRI Configuration 54
- T1 Channelized Mode 57
- Switched Mode 59
- Dedicated Mode 59
- Completing the Configuration 60
- • Power on the router 71
- Configuring ISDN BRI Lines 74
- Configuring T1 Interfaces 77
- Configuring E1 Interfaces 78
- Configuring Codec Complexity 80
- Default Configuration 81
- Configuring ATM Interfaces 82
- Configuring PVCs 83
- Configuring SVCs 84
- Configuring the IMA Interface 87
- Benefits 92
- Verifying ATM Configuration 94
- Serial Communication Channels 97
- Asynchronous Craft Port 98
- Serial Data Channel 98
- Configuring the AIC 100
- Accessing the AIC 102
- Configuring Alarms 103
- Verifying the IP Address 105
- Troubleshooting Tips 107
- Software Upgrade 107
- Configuration Examples 108
- Configuration Tasks 109
- Cisco 3600 Series Routers 111
- Cisco 3640 Router 112
- Prerequisites 113
- Configure the LAN Interface 117
- Configuration Example 120
- Restrictions 122
- Verifying ATM Configuration 124
- Saving Configuration Changes 127
- Where to Go Next 127
- Configuring Voice-over-IP 129
- Router SJ Configuration 135
- Router SLC Configuration 136
- • IMA-8T1 in 146
- • NM-4A/S 146
- • WIC-2A/S 146
- • WIC-1DSU-56k4 146
- With an Unnumbered IP Address 160
- Discrete Alarm 162
- Modem Calls 163
- Formatting Procedures 171
- File and Directory Operations 174
- Display File Content 176
- Copy Files 177
- Rename a File 179
- Create a New Directory 180
- Remove a Directory 181
- Using the ROM Monitor 183
- ROM Monitor Commands 184
- Command Descriptions 185
- Debugging Commands 187
- Using the xmodem Command 190
- Using the tftpdnld Command 190
- Entering the ROM Monitor Mode 192
- Numerics 193
Verwandte Produkte und Handbücher für Vernetzung Cisco 3631
Vernetzung Cisco 2650 - 2650 Router Spezifikationen
(266 Seiten)
(266 Seiten)
Vernetzung Cisco SRW224 Bedienungsanleitung
(5 Seiten)
(5 Seiten)
Vernetzung Cisco ASR1004-10G-SHA/K9 - ASR 1004 Sec+HA Bundle Router Bedienungsanleitung
(105 Seiten)
(105 Seiten)
Vernetzung Cisco 3800 Series Spezifikationen
(40 Seiten)
(40 Seiten)
Vernetzung Cisco 1802 Spezifikationen
(198 Seiten)
(198 Seiten)
Vernetzung Cisco SOHO 71 Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Vernetzung Cisco WS-C2950ST-24-LRE - Syst. 24PORT 2950-BASED LONG REACH Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Vernetzung Cisco DPC3825 Bedienungsanleitung
(109 Seiten)
(109 Seiten)
Vernetzung Cisco EPC3825 Bedienungsanleitung
(35 Seiten)
(35 Seiten)
Vernetzung Cisco SRW208MP Bedienungsanleitung
(14 Seiten)
(14 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern