Cisco ONS 15327 Spezifikationen Seite 223
- Seite / 334
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
3-173
Cisco ONS 15454 and Cisco ONS 15327 TL1 Command Guide, R3.3
May 2002
Chapter 3 TL1 Command Descriptions
TL1 Commands
3.5.122 SET-ATTR-CONT: Set Attribute Control
This command instructs the NE to set the attributes associated with an external control. The attributes
are used when an external control is operated or released. To send the attributes, use the
RTRV-ATTR-CONT command.
Note If the <CONTTYPE> parameter is not specified, the control specified by <AID> is unprovisioned.
Output Format SID DATE TIME
M CTAG COMPLD
“<AID>::[RVRTV=<RVRTV>,][RVTM=<RVTM>,][TACC=<TACC>]”
;
where:
• <AID> is the access identifier from the “VT1_5” section on page 4-17
• <RVRTV> is the revertive mode which only applies to UPSR VT1 path.
<RVRTV> defaults to N (non-revertive mode) when UPSR VT1 is created; valid
values for <RVRTV> are shown in the “ON_OFF” section on page 4-51 and
<RVRTV> is optional
• <RVTM> is the revertive time which only applies to UPSR VT1.<RVTM>
defaults to empty because <RVRTV> is N when UPSR VT1 is created. Valid
values for <RVTM> are shown in the “REVERTIVE_TIME” section on
page 4-55 and <RVTM> is optional.
• <TACC> defines the STS as a test access port with a selected unique TAP
number. The TAP number ranges from 0–999; <TACC> is optional.
Output
Example
TID-000 1998-06-20 14:30:00
M 001 COMPLD
“VT1-2-4-1-2::RVRTV=Y,RVTM=1.0,TACC=8”
;
Errors This message generates all the default errors
Section RTRV-VT1 Description (continued)
Section SET-ATTR-CONT Description
Category Environmental Alarms and Controls
Security Provisioning
Related
Messages
OPR-EXT-CONT RTRV-ATTR-CONT
REPT ALM ENV RTRV-ATTR-ENV
REPT EVT ENV RTRV-COND-ENV
RLS-EXT-CONT RTRV-EXT-CONT
RTRV-ALM-ENV SET-ATTR-ENV
- TL1 Command Guide 1
- 1 Getting Started 1-1 3
- 2 TL1 Gateway 2-1 4
- 4 TL1 Command Components 4-1 8
- Contents 10
- May 2002 10
- 5 Ring Provisioning 5-1 12
- 7 TL1 Alarms and Errors 7-1 12
- About This Manual 23
- Related Documentation 24
- Conventions 24
- Obtaining Documentation 25
- Ordering Documentation 26
- Documentation Feedback 26
- Cisco.com 26
- Technical Assistance Center 27
- Cisco TAC Escalation Center 28
- Getting Started 29
- 1.1.1 Open a TL1 session 30
- Setting up TL1 Communication 31
- 1.2 TL1 Command Syntax 32
- 1.3 Autonomous Messages 33
- Table 1-1 Command Access 34
- Table 1-2 Security Idle Times 34
- 1.7.1 General Rules 35
- 1.8 Test Access 37
- 1.8.1 Mode Definitions 38
- Test Access 39
- 1.8.3 Loop E and F Modes 40
- Figure 1-12 SPLTA access 41
- Figure 1-13 SPLTB access 41
- TL1 Gateway 45
- Chapter 2 TL1 Gateway 46
- Allocated 47
- 2.2 Implementing TL1 Gateway 48
- Log Into a Remote ENE 49
- Log Out of a Remote ENE 49
- Implementing TL1 Gateway 50
- TL1 Command Descriptions 51
- TL1 Commands by Category 52
- 3.5 TL1 Commands 80
- 3.5.7 CANC: Cancel 85
- 3.5.8 CANC-USER: Cancel User 86
- STS48C, STS192C) 96
- TL1 Commands 100
- 3.5.26 ED-G1000: Edit G1000 106
- 3.5.29 ED-PID: Edit Password 109
- OC48, OC192) 121
- OC48, OC192, T1, T3) 132
- STS192C, T1, T3, VT1) 137
- STS24C, STS48C, STS192C) 162
- STS48C, STS192C, T1, T3, VT1) 181
- TL1 Command Components 233
- 4.1.4 Equipment 234
- 4.1.5 Performance 234
- 4.1.6 Ports 235
- 4.1.7 SONET Line Protection 236
- 4.1.8 STS and VT Paths 236
- 4.2 Access Identifiers 237
- Access Identifiers 238
- 4.2.2 CrossConnectID 239
- 4.2.3 PRSLOT 240
- 4.2.4 BITS 241
- 4.2.5 BLSR 241
- 4.2.6 DS1 242
- 4.2.7 ENV 242
- 4.2.8 EQPT 243
- 4.2.9 FACILITY 243
- 4.2.10 STS 244
- 4.2.10.2 STS for ONS 15327 245
- 4.2.11 SYN 246
- 4.2.12 SYN_SRC 246
- 4.2.13 SYNC_REF 247
- 4.2.14 SYNCSW 248
- 4.2.15 TAP 249
- 4.2.16 VT1_5 249
- 4.3 Parameter Types 250
- 4.3.4 Parameter Notes 251
- 4.3.5 ALL_MONTYPE 251
- 4.3.6 ALL_THR 252
- Parameter Types 253
- 4.3.7 BITS_LineBuildOut 254
- 4.3.8 BLSR_MODE 254
- 4.3.9 BLSR_TYPE 255
- 4.3.10 CCT 255
- 4.3.11 CMD_MODE 255
- 4.3.12 COND_EFF 256
- 4.3.13 CONDITION 256
- September 2002 258
- 4.3.14 CONT_MODE 266
- 4.3.15 CONTTYPE 266
- 4.3.16 CRS_TYPE 266
- 4.3.17 DIRECTION 267
- 4.3.18 DIRN 267
- 4.3.19 DS3_FMT 267
- 4.3.20 DS_LINE_CODE 267
- 4.3.21 DS_LINE_TYPE 268
- 4.3.22 DURATION 268
- 4.3.23 E_LBO 268
- 4.3.24 ENV_ALM 268
- 4.3.25 ENV_CRTL_MODE 270
- 4.3.26 EQPT_TYPE 270
- 4.3.27 EQUIP 272
- 4.3.28 EQUIPMENT_TYPE 272
- 4.3.29 EXT_RING 273
- 4.3.30 FLOW 273
- 4.3.31 FRAME_FORMAT 273
- 4.3.32 LINE_BUILDOUT 274
- 4.3.33 LINE_CODE 274
- 4.3.34 LOCATION 274
- 4.3.35 LPBK_TYPE 275
- 4.3.36 MFS_TYPE 275
- 4.3.37 MOD2 275
- 4.3.38 MOD2_IO 276
- 4.3.39 MOD2ALM 276
- 4.3.40 MOD2B 277
- 4.3.41 MOD_PATH 278
- 4.3.42 MOD_PORT 279
- 4.3.43 MOD_TACC 279
- 4.3.44 MODIFIER 280
- 4.3.45 MODULE_OP 280
- 4.3.46 MSGTYPE 281
- 4.3.47 MUX_TYPE 281
- 4.3.48 NOTIF_CODE 281
- 4.3.49 OCN_4F 282
- 4.3.50 OCN_BLSR 282
- 4.3.51 OCN_MONTYPE 282
- 4.3.54 OPTICAL_MODE 283
- 4.3.55 OPTICS 283
- 4.3.52 OCN_TYPE 283
- 4.3.53 ON_OFF 283
- 4.3.56 PM_MODE 284
- 4.3.57 PM_STATE 284
- 4.3.58 PRIVILEGE 284
- 4.3.59 PRODUCT_TYPE 285
- 4.3.60 PROTECTION_GROUP 285
- 4.3.61 PST 285
- 4.3.62 PSTQ 286
- 4.3.63 REVERTIVE_TIME 287
- 4.3.64 RNG_TYPE 287
- 4.3.65 SD_BER 287
- 4.3.66 SDCC_MODE 287
- 4.3.67 SERV_EFF 288
- 4.3.68 SF_BER 288
- 4.3.69 SIDE 288
- 4.3.70 SST 288
- 4.3.71 STATE 289
- 4.3.72 STATUS 289
- 4.3.73 STM_TYPE 290
- 4.3.74 STS_MAP 290
- 4.3.75 STS_MONTYPE 290
- 4.3.76 STS_PATH 291
- 4.3.77 SWITCH 291
- 4.3.78 SWITCH_TYPE 291
- 4.3.80 SYNC_GENERATION 292
- 4.3.81 SYNC_MODE 292
- 4.3.82 SYNC_QUALITY_LEVEL 293
- 4.3.83 T1_MONTYPE 293
- 4.3.84 T3_MONTYPE 294
- 4.3.85 TACC_MODE 294
- 4.3.86 TIMING_MODE 295
- 4.3.87 TMG_REF 295
- 4.3.88 TMPER 295
- 4.3.89 TRCMODE 296
- 4.3.90 UNI_BI 296
- 4.3.91 USE_DST 296
- 4.3.92 VALIDITY 296
- 4.3.93 VT1_5_MONTYPE 297
- Ring Provisioning 299
- Ring-to-Ring Interconnection 300
- 5.4 1WAY Drop and Continue 307
- 1WAY Drop and Continue 308
- TL1 Performance Monitoring 309
- Far-End Line 310
- Near-End VT Path 313
- Far-End VT Path 313
- PM Parameters by Line Type 314
- TL1 Alarms and Errors 315
- 7.1.1 AIP 316
- 7.1.2 BITS 316
- 7.1.3 BPLANE 317
- 7.1.4 DS1 317
- 7.1.5 DS3 317
- 7.1.6 E1000F 318
- 7.1.7 E100(T) 318
- 7.1.8 EC1-12 318
- 7.1.9 ENVALRM 318
- 7.1.10 EQPT 319
- 7.1.11 EXT-SREF 320
- 7.1.12 FAN 320
- 7.1.13 G1000 321
- 7.1.14 NE 321
- 7.1.15 NE-SREF 322
- 7.1.16 OCN 322
- 7.1.17 STSMON 323
- 7.1.18 STSTRM 324
- 7.1.19 VT-MON 324
- 7.1.20 VT-TERM 324
- 7.2 Errors 325
- 7.3 Echo 330
Verwandte Produkte und Handbücher für Vernetzung Cisco ONS 15327
Vernetzung Cisco 521 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Vernetzung Cisco NMH300 Installationsanleitung
(32 Seiten)
(32 Seiten)
Vernetzung Cisco CTX2500 Technical Information
(30 Seiten)
(30 Seiten)
Vernetzung Cisco WMA11B Betriebsanweisung
(32 Seiten)
(32 Seiten)
Vernetzung Cisco 7301 Technical Information
(40 Seiten)
(40 Seiten)
Vernetzung Cisco SPA3102 Betriebsanweisung
(100 Seiten)
(100 Seiten)
Vernetzung Cisco WRT150N Betriebsanweisung
(90 Seiten)
(90 Seiten)
Vernetzung Cisco PIX-515E Spezifikationen
(78 Seiten)
(78 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.187 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern