Cisco GoQAM Technical Information Seite 289
- Seite / 308
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Post-Amplifier FTTP Parameters
4025561 Rev
A
265
Alarm Function
Major
Low
Threshold
Minor
Low
Threshold
Minor
High
Threshold
Major
High
Threshold
Hys-
teresis
Typical
Range/
Nom.
Value
ServiceB Service
mode B
na na na na na OK or
Fault [4]
Note:
[1] This alarm threshold value is relative to the nominal alarm value.
[2] This alarm sets the unit to the safe state, in which the optical input is disabled.
[3] The factory default is Fault, where the alarm values OK and Fault correspond
to the control values ON and OFF, respectively. The module must be user-
enabled following installation.
[4] The alarm values OK and Fault correspond to the control values OFF and
ON, respectively.
Post-Amplifier Control Parameters
Control Function
Possible
Values
Default
Enable Turns optical amplifier ON or OFF ON (1)
OFF (0)
OFF (0)
SetAtten Optical power attenuation 0 to 3 dB in
0.5 dB steps
0
Master When set to slave (0), will only start with
an external alarm signal
Master (1)
Slave (0)
Master (1)
ServiceA Reduces Output A optical power to +15
dBm for servicing
ON (1)
OFF (0)
OFF (0)
ServiceB Reduces Output B optical power to +15
dBm for servicing
ON (1)
OFF (0)
OFF (0)
Post-Amplifier Manufacturing Parameter Examples
24 x 17.65 dBm Module
Manufacturing Data Typical Values
Set in Manufacturing
(example value shown)
Module Name 1550 nm Post-Amp FTTP
- Prisma II EMS 1
- Remote User Interface 1
- Guide - System Release 2.04 1
- For Your Safety 3
- Notices 4
- Contents 5
- Contents 7
- Glossary 275 8
- Index 281 8
- Prisma II Product Notices 9
- Read and Retain Instructions 11
- Terminology 11
- Electric Shock Hazard 11
- Installation Site 12
- Installation Requirements 12
- Equipment Placement 12
- Ventilation 13
- Handling Precautions 14
- Grounding 14
- Equipotential Bonding 14
- Circuit Overload 15
- Electrostatic Discharge 16
- Fuse Replacement 16
- Batteries 16
- Modifications 17
- Accessories 17
- EMC Compliance Statements 18
- Laser Safety 19
- Warning Labels 21
- 23
- 1 Chapter 1 25
- Qualified Personnel 26
- Document Version 26
- Related Publications 27
- 1.01, part number 4015396 28
- What's New 29
- 2 Chapter 2 31
- Configuration 32
- User Authorization 33
- CLI Login and Logout 34
- CLI Command Modes 36
- CLI Command Modes 37
- Command Syntax 38
- Non-Modal Command Syntax 39
- Command Usage Guidelines 40
- Command Syntax 41
- General Hints and Help 42
- Alarm Information 43
- Getting Online Help 43
- 3 Chapter 3 45
- CLI> alarm 46
- No active alarms found 46
- CLI> 46
- clear 47
- CLI> date 48
- Tue, 3 Oct 2006 11:36:43 EST 48
- CLI> logout 52
- logout 53
- terminal 57
- CLI> who 58
- whoami 59
- 4 Chapter 4 61
- About Modspecs 65
- Notes on Usage 67
- 20/* MODULE> alarm 68
- 20/* MODULE> 68
- alarm domain 69
- 20/[5-7] MODULE> 70
- */* MODULE> logout 84
- reset 91
- Access Rights Required 100
- Example 100
- Related Commands 101
- Description 102
- Parameters 102
- Examples 102
- Transmitter (devtype: 1033) 105
- show module 115
- 5 Chapter 5 123
- In This Chapter 124
- Overview 125
- To Access ICIM Command Mode 126
- alarm 127
- ICIM> eventlogclear 128
- SUCCESS! 128
- ICIM> 128
- ICIM> logout 144
- C:\> 144
- manual 147
- ICIM> reboot 150
- show domain 159
- show eventlogall 161
- show file 163
- show iproute 165
- show traps 169
- traps 173
- Parameter Description 173
- ICIM> user delete smith8 178
- user unlock 179
- 6 Chapter 6 181
- TERMINAL> logout 191
- paging 195
- 7 Chapter 7 201
- Introduction 202
- Introduction 203
- Installation 204
- Web Browser Setup 205
- Login and Logout 207
- To Log Out 209
- To Change Login Defaults 209
- Using System View 211
- To View Module Summary 212
- To View Current Alarms 212
- Using System View 213
- Using ICIM Details 214
- To Work with ICIM Details 215
- Using Module Details 217
- To View Module Details 218
- To View Alarms 219
- To View Thresholds 219
- To View Controls 220
- To View Monitors 221
- Using System Settings 224
- Event Log Settings 225
- SNMP Traps 225
- Using the Event Log 227
- To Clear the Event Log 228
- User Management 229
- To Edit an Existing User 230
- To Review Current Users 231
- Web Interface Help 232
- To Use Navigate by Keywords 233
- 8 Chapter 8 235
- Obtaining Product Support 236
- Obtaining Product Support 237
- Return Product for Repair 238
- Return Product for Repair 239
- A Appx auto letter 245
- From CLI 246
- From ICIM 247
- Appendix A 252
- '?' 252
- From */* MODULE 253
- From TERMINAL 256
- B Appx auto letter 257
- ICIM Data 259
- Module Data 262
- Current Alarms 263
- Module Alarms 264
- Module Controls 265
- Module Monitors 266
- System Information 267
- C Appx auto letter 269
- In This Appendix 270
- Fan Tray 271
- Alarm Parameters 272
- Monitor Parameters 272
- Control Parameters 273
- Fan Tray Parameters (Split) 277
- 2 x 19 dBm Module 285
- 24 x 17.65 dBm Module 290
- Glossary 299
- Index 307
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.180 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern