Cisco GoQAM Technical Information PDF herunterladen (Seite 148)

Cha

5 ICIM Mode Commands

124 4025561

Rev

set <parameter> <value>

Use the 'set' command to set any of the user-changeable ICIM2

values. Following are the parameters available for modification:

clli Common Language Locator ID code for ICIM

clock The ICIM2 real time clock (value MUST be in quotes)

commread SNMP Read Community string

commtrap SNMP Trap Community string

commwrite SNMP Write Community string

gateway IP address of TCP/IP gateway, for packet routing

ip TCP/IP address of the ICIM

lockout Lockout interval in minutes (0 disables lockout)

statusmsgclearkey Set to 1 to clear the status message

subnet Subnet mask, such as 255.255.255.0

threshold Use the 'set threshold' command to set the login

threshold number. Valid values are 0-15, where 0

disables threshold checking.

timeout Use the 'set timeout' command to set the user

inactivity timeout. Once a user session has been

inactive for this many minutes, the user will be

automatically logged out of the system. Valid values

are from 1 to 60. Changes to timeout affect future

console, Telnet and Web sessions.

tzone Time zone string

updateid Set to 1 to have the system read a new chassis ID

And here are some examples of using the 'set' command:

ICIM> set commread public

ICIM> set clock "9/12/2006 14:21:30"

ICIM> set updateid 1

show

Use the 'show' command to display one or more ICIM parameter values.

Any number of available parameters can be requested with the same command.

Exception commands are those that return multi-word replies: clock, domain

eventlog, eventlogall, eventlogfilter, file, ike, iproute, provisioning,

traps and user. These must be entered separately.

Examples of valid commands:

ICIM> show activerev

ICIM> show commread commwrite clei

The 'show' command can be used to display all of the parameters that

are supported by the 'info' command, plus these:

clock The ICIM2 real time clock

domain The complete module listing for this ICIM domain

eventlog The ICIM2 event log with only the timestamp, user and

description fields to make console viewing simpler

eventlogall The ICIM2 event log with all fields

eventlogfilter The filter settings for the event logging

file The file management settings for FTP transfer of event log

ike The Internet Key Exchange settings

iproute The IP Route settings

lockedusers The currently locked user accounts

provisioning The commands needed to restore the module configuration

sntp The SNTP settings to synchronize the RTC with the NTP Server

traps The trap receiver table settings

user The table of configured user accounts

sntp <parameter> <value>

Use the 'sntp' command to change the settings to synchronize the

ICIM's Real Time Clock with the Network Time Protocol Server.

Last of all, activate SNTP by changing sntp state to 'enable'.

Following are examples of settings for these values:

ICIM> sntp mode <unicast | broadcast>

ICIM> sntp ip <ip address>

ICIM> sntp timeout <seconds>

ICIM> sntp interval <hours>

ICIM> sntp state <enable | disable>

To show the current settings, use the 'show sntp' command.

traps <state> <index> <ip_address>

Use the 'traps' command to modify the trap receiver table. The table

holds 10 trap receivers, indexed 0 to 9. If a receiver entry already

exists and its state is being modified, it is not necessary to use the

<ip_address> parameter. Examples:

ICIM> traps enable 0 192.32.101.12

ICIM> traps disable 3

1 2 ... 143 144 145 146 147 148 149 150 151 152 153 ... 307 308

Kommentare zu diesen Handbüchern

Keine Kommentare

Cisco GoQAM Technical Information Seite 148

Kommentare zu diesen Handbüchern