Cisco 2525 Betriebsanweisung Seite 115
- Seite / 166
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Maintaining the Cisco 2524 and Cisco 2525 Routers A-3
Opening the Chassis
Step 4 Tighten the two captive screws on the module to secure it to the chassis.
Caution Although there are three slots available for the WAN modules, the slot on the far
right (labeled BRI 0) is reserved for an ISDN WAN module only. Install all other modules
in the slots labeled SERIAL 0 and SERIAL 1. The ISDN WAN modules are designed so
that you cannot insert them into the synchronous serial slots.
Figure A-1 Installing a WAN Module
Step 5
If your router is configured with less than three WAN modules, make sure a blank
slot cover is installed over each open slot to ensure proper airflow inside the
chassis.
Opening the Chassis
This section describes the procedure for opening the chassis by removing the chassis cover.
Warning Do not touch the power supply when the power cord is connected. For systems
with a power switch, line voltages are present within the power supply even when the power
switch is OFF and the power cord is connected. For systems without a power switch, line
voltages are present within the power supply when the power cord is connected. (To see
translated versions of this warning, refer to the appendix “Translated Safety Warnings.”)
H5259
BRI 0
Router
Card guide
ISDN-BRI
ACTIVITY
- About This Guide 1
- Document Organization 2
- Document Conventions 3
- Safety Warnings.”) 4
- Overview of the Cisco 2524 5
- Features 10
- Specifications 11
- FCC Part 68 13
- Preparing to Install the 15
- Cisco 2524 and Cisco 2525 15
- Safety Recommendations 16
- Site Environment 18
- Preventive Site Configuration 18
- Configuring Equipment Racks 19
- Power Supply Considerations 19
- Installation Checklist 20
- Creating a Site Log 22
- 1. kHz = kilohertz 23
- ISDN Connections 26
- 1. nF = nanoFarad 27
- Ethernet Connections 29
- Token Ring Connections 29
- Console Port Connections 30
- Auxiliary Port Connections 30
- Inspecting the System 31
- Installing the Cisco 2524 and 33
- Required Tools and Parts 34
- Setting Up the Chassis 35
- Rack-Mounting the Chassis 36
- Attaching the Brackets 37
- Figure 3-6 or Figure 3-7 38
- Figure 3-8 or Figure 3-9 39
- Installing in a Rack 40
- Wall-Mounting the Chassis 41
- SERIAL 1 42
- SERIAL 0 42
- DC Power Specifications 43
- Wiring the DC Power Supply 44
- Input: –40––72V 45
- Current: 1.5–1.0A 45
- Watts: 40W 45
- Connecting to the Network 46
- Connecting to a WAN 51
- Figure 3-20.) 52
- Figure 3-21.) 53
- Figure 3-22.) 54
- ACTIVITY 55
- Console port 59
- RJ-45 roll-over cable 59
- RJ-45-to-DB-25 adapter 59
- Configuring the Cisco 2524 and 63
- Configuring the Router 64
- Using Configuration Mode 65
- Using AutoInstall 66
- Configuring the Router 67
- Configuring ISDN 76
- Configuring Switched 56 78
- Configuring DDS 79
- Specifying the Boot Method 82
- Getting More Information 84
- Cabling Specifications for the 85
- Identifying a Roll-Over Cable 86
- Pin 1 and pin 8 87
- (labeled Terminal) 88
- (labeled Modem) 89
- Token Ring Port Pinouts 93
- RJ-48C jack 94
- EIA/TIA-232 97
- EIA/TIA-449 99
- <— indicates DCE to DTE 102
- APPENDIX 109
- Running Diagnostic Tests 111
- Getting Help 111
- Cisco 2525 Routers 113
- Installing WAN Modules 114
- Opening the Chassis 115
- Tools Required 116
- Removing the Chassis Cover 116
- Screw Slot 117
- Flat-blade screwdriver 117
- CODE0CODE1 118
- Upgrading the DRAM SIMM 119
- Tools and Equipment Required 121
- DRAM SIMM Installation 121
- System-Code SIMM Replacement 123
- Replacing the Cover 126
- Recovering Lost Passwords 127
- (Router#): 132
- > b [tftp] flash filename 134
- Translated Safety Warnings 141
- Product Disposal Warning 142
- Jewelry Removal Warning 143
- Ground Connection Warning 144
- Installation Warning 145
- TN Power Warning 146
- Circuit Breaker (15A) Warning 146
- SELV Circuit Warning 148
- ISDN Connection Warning 152
- Qualified Personnel Warning 154
- Restricted Area Warning 155
- DC Power Supply Warning 159
- DC Power Connection Warning 160
- Lightning Activity Warning 161
- Grounded Equipment Warning 162
- Power Supply Warning 164
Verwandte Produkte und Handbücher für Vernetzung Cisco 2525
Vernetzung Cisco IOS Router Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Vernetzung Cisco EPC3208 Bedienungsanleitung
(74 Seiten)
(74 Seiten)
Vernetzung Cisco 1710 Spezifikationen
(88 Seiten)
(88 Seiten)
Vernetzung Cisco WRT300N Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Vernetzung Cisco Linksys E-Series Betriebsanweisung
(139 Seiten)
(139 Seiten)
Vernetzung Cisco 7202 Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Vernetzung Cisco DPQ2202 Bedienungsanleitung
(164 Seiten)
(164 Seiten)
Vernetzung Cisco PA-T3 Spezifikationen
(74 Seiten)
(74 Seiten)
Vernetzung Cisco CCNA NETWORK SIMULATOR Handbuch
(19 Seiten)
(19 Seiten)
Vernetzung Cisco E1200 Betriebsanweisung
(48 Seiten)
(48 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.543 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern