Cisco MC3810 Installationsanleitung PDF herunterladen (Seite 26)

Configuring Voice Ports

Release 12.0(7)XK

router(config-voiceport)# timing clear-wait

milliseconds

Specify the number of milliseconds between the inactive seizure

signal and the call being cleared. The range is 100 to 2000. The

default is 400.

router(config-voiceport)# timing delay-duration

milliseconds

Specify the delay signal duration in milliseconds for delay dial

signaling. This command applies only if the signal command is

set to delay-dial. The range is 100 to 5000. The default is 140.

router(config-voiceport)# timing delay-start

milliseconds

Specify the number of milliseconds of delay from the outgoing

seizure to the outdial address. This value applies only if the

signal command is set to delay-dial. The range is 100 to 290.

The default is 150.

router(config-voiceport)# timing dialout-delay

milliseconds

Conﬁgure the delay interval before sending a dialed digit or

cut-through. This value applies only if the signal command is set

to immediate. The range is 100 to 5000. The default is 300.

router(config-voiceport)# timing

delay-with-integrity

milliseconds

Specify the number of milliseconds duration of the wink pulse

for delay dials. The range is 0 to 5000. The default is 0.

router(config-voiceport)# timing dial-pulse

min-delay

milliseconds

If the dial type is pulse, specify the number of milliseconds

between generation of wink-like pulses. The range is 140 to

5000. The default is 140.

router(config-voiceport)# timing wink-duration

milliseconds

Specify the length in milliseconds of the wink-start signal. This

command applies only if the signal command is set to

wink-start. The range is from 100 to 400 milliseconds and the

default is 200.

router(config-voiceport)# timing wink-wait

milliseconds

Specify the wink-wait duration in milliseconds for a wink-start

signal. This command applies only if the signal command is set

to wink-start. The range is 100 to 5000. The default is 200.

router(config-voiceport)# timing percentbreak

percent

Specify the percentage of the break period for dialing pulses. The

range is 20 to 80. The default is 50.

router(config-voiceport)# timing digit

milliseconds

If the dial type is DTMF, conﬁgure the DTMF digit signal

duration in milliseconds. The range is 50 to 100. The default is

100.

router(config-voiceport)# timing inter-digit

milliseconds

If the dial type is DTMF, conﬁgure the DTMF inter-digit signal

duration in milliseconds. The range is 50 to 500. The default is

100.

router(config-voiceport)# timing pulse

pulses-per-second

If the dial type is pulse, specify the pulse dialing rate in pulses

per second. The range is 10 to 20. The default is 10.

router(config-voiceport)# timing pulse-digit

milliseconds

If the dial type is pulse, specify the pulse digit duration in

milliseconds. The range is 10 to 20. The default is 20.

router(config-voiceport)# timing

pulse-inter-digit

milliseconds

If the dial type is pulse, conﬁgure the pulse inter-digit duration in

milliseconds. The range is 100 to 1000. The default is 500.

router(config-voice-port)#exit

Exit from voice-port conﬁguration mode.

Step Command Purpose

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 77 78

Kommentare zu diesen Handbüchern

Keine Kommentare

Cisco MC3810 Installationsanleitung Seite 26

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Faxgeräte Cisco MC3810