Cisco 2950 - Catalyst Switch Spezifikationen Seite 139
- Seite / 674
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-113
Catalyst 2950 and Catalyst 2955 Switch Command Reference
OL-10102-02
Chapter 2 Catalyst 2950 and 2955 Cisco IOS Commands
errdisable recovery
Defaults Recovery is disabled for all causes.
The default interval is 300 seconds.
Command Modes Global configuration
Command History
Usage Guidelines A cause (for example, bpduguard) is defined as the reason why the error-disabled state occurred. When
a cause is detected on an interface, the interface is placed in error-disabled state, an operational state
similar to link-down state. If you do not enable errdisable recovery for the cause, the interface stays in
error-disabled state until you enter a shutdown and no shutdown interface configuration command. If
you enable the recovery for a cause, the interface is brought out of the error-disabled state and allowed
to retry the operation again when all the causes have timed out.
Otherwise, you must enter the shutdown and then no shutdown commands to manually recover an
interface from the error-disabled state.
Examples This example shows how to enable the recovery timer for the BPDU guard error-disable cause:
Switch(config)# errdisable recovery cause bpduguard
This example shows how to set the timer to 500 seconds:
Switch(config)# errdisable recovery interval 500
You can verify your settings by entering the show errdisable recovery privileged EXEC command.
Related Commands
Release Modification
12.1(6)EA2 This command was introduced.
12.1(9)EA1 The gbic-invalid and psecure-violation keywords were added. The
rootguard keyword was removed.
12.1(13)EA1 The channel-misconfig keyword was added.
12.1(19)EA1 The dhcp-rate-limit and loopback keywords were added.
Command Description
show errdisable recovery Displays errdisable recovery timer information.
show interfaces status Displays interface status.
- Command Reference 1
- CONTENTS 3
- Contents 10
- OL-10102-02 10
- B-10 12
- Audience 15
- Conventions 15
- Related Publications 16
- Type of Memory 19
- Platforms 19
- CLI Command Modes 20
- User EXEC Mode 21
- Privileged EXEC Mode 21
- Global Configuration Mode 22
- Interface Configuration Mode 22
- VLAN Configuration Mode 23
- Line Configuration Mode 23
- Command Summary 24
- Command Summary 26
- aaa authentication dot1x 30
- access-list (IP extended) 31
- access-list (IP standard) 34
- • The syntax for the FTP: 36
- • The syntax for the TFTP: 38
- archive tar 39
- archive upload-sw 42
- auto qos voip 44
- boot boothlpr 47
- boot buffersize 48
- boot config-file 49
- boot enable-break 50
- boot helper 51
- boot helper-config-file 52
- boot manual 53
- boot private-config-file 54
- boot system 55
- channel-group 56
- channel-protocol 60
- class 61
- class-map 63
- clear controllers lre log 69
- clear mac address-table 73
- clear vmps statistics 80
- Switch# clear vmps statistics 80
- clear vtp counters 81
- Switch# clear vtp counters 81
- cluster enable 85
- cluster management-vlan 87
- cluster member 88
- cluster run 90
- cpe toggle 103
- define interface-range 105
- delete 107
- Switch# delete flash:filename 107
- • Class of service (CoS) 112
- dot1x 114
- dot1x auth-fail vlan 116
- dot1x default 120
- dot1x guest-vlan 121
- dot1x initialize 124
- dot1x max-req 125
- dot1x multiple-hosts 126
- dot1x port-control 127
- dot1x re-authenticate 129
- dot1x re-authentication 130
- dot1x timeout 132
- duplex 134
- errdisable detect cause 136
- errdisable recovery 138
- flowcontrol 140
- hw-module slot 144
- (nonrouting) port 148
- interface port-channel 149
- interface range 150
- • fastethernet interface-id 151
- interleave 152
- ip access-group 154
- ip access-list 156
- ip dhcp snooping 159
- ip dhcp snooping trust 165
- ip dhcp snooping vlan 166
- ip igmp max-groups 168
- IGMP profile number 171
- ip igmp snooping 172
- ip ssh 185
- lacp port-priority 187
- lacp system-priority 189
- lre profile 200
- 1. Per-port sequence 201
- 2. Global sequence 201
- 3. Port profile 201
- 4. Global profile 201
- lre syslog 205
- Switch(config)# lre syslog 205
- lre upbo 206
- Switch# configure terminal 207
- Related Commands 207
- mac access-group 211
- mac access-list extended 213
- mac address-table static 218
- macro apply 222
- macro description 225
- macro global 226
- macro global description 228
- macro name 229
- margin 231
- match 233
- media-type 236
- mls qos cos 238
- mls qos map 239
- mls qos trust 242
- monitor session 245
- mvr immediate 251
- mvr type 253
- pagp learn-method 256
- pagp port-priority 258
- police 265
- policy-map 267
- port-channel load-balance 270
- rate selection 276
- rate selection sequence 279
- rcommand 280
- remote-span 283
- 0L-10102-02 289
- VLAN is configured: 343
- command to display an 465
- • 1000 Mbps—20000 478
- • 100 Mbps—200000 478
- • 10 Mbps—2000000 478
- Switch(config)# udld enable 541
- Switch# vmps reconfirm 563
- Switch(config)# vmps retry 7 564
- Catalyst 2955 Alarm Commands 581
- power-supply dual 590
- show alarm settings 595
- test relay 601
- Switch# test relay major on 601
- Boot Loader Commands 603
- boot 604
- • d—directory 609
- • r—readable 609
- • w—writable 609
- • x—executable 609
- flash_init 610
- format 611
- [-test 612
- help 613
- load_helper 614
- memory 616
- more 618
- rename 619
- rmdir 621
- type 625
- unset 626
- APPENDIX 629
- debug auto qos 631
- debug dot1x 632
- debug etherchannel 633
- debug lre 634
- debug pagp 635
- debug pm 636
- debug spanning-tree 638
- debug spanning-tree bpdu 641
- debug spanning-tree mstp 643
- debug switch dhcp 648
- debug sw-vlan 649
- debug sw-vlan ifs 651
- debug sw-vlan vtp 654
- debug udld 656
- Numerics 659
Verwandte Produkte und Handbücher für Software Cisco 2950 - Catalyst Switch
Software Cisco Aironet 1200 Series Spezifikationen
(364 Seiten)
(364 Seiten)
Software Cisco ROUTER-SDM-CD Betriebsanweisung
(20 Seiten)
(20 Seiten)
Software Cisco HWIC Installationsanleitung
(82 Seiten)
(82 Seiten)
Software Cisco Aironet 700 Series Spezifikationen
(402 Seiten)
(402 Seiten)
Software Cisco ROUTER-SDM-CD Betriebsanweisung
(74 Seiten)
(74 Seiten)
Software Cisco IAD2431-1T1E1 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Software Cisco LightStream 1010 Spezifikationen
(89 Seiten)
(89 Seiten)
Software Cisco 3130 Spezifikationen
(107 Seiten)
(107 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern