Cisco Aironet 1000 Series Installationsanleitung Seite 1

Quick Start GuideCisco Aironet 1000 Series Lightweight Access PointsINCLUDING LICENSE AND WARRANTY1 About this Guide2 Safety Information3 Introductio

10 • Make sure that your network infrastructure devices are operational and properly configured.• Verify that the wireless LAN controllers are connect

11 The access point must be able to find the IP address of the controller by using DHCP, DNS, OTAP, or IP subnet broadcast. This guide describes the D

12 After the access point finds a master controller, the access point compares its operating system version code with that running on the controller.

13 Priming the Access PointThis section describes the optional procedure for priming or staging your access point before it is installed. Priming migh

14 Note For a Layer 3 access point on a different subnet than the controller, ensure that the access point subnet has a DHCP server and a route to the

15 Step 7 If the access point is in a controller mobility group, configure the controller mobility group name.Step 8 Configure the access point-specif

16 Where: <pool name> is the name of the DHCP pool, such as AP1000<IP Network> is the network IP address where the controller resides, suc

17 Step 4 In the Contact Cisco for Support frame, click Email or phone Technical Support. The Technical Support and Documentation Cisco Worldwide Cont

18 Checking the Access Point LEDsIf your access point is not working properly, check the access point LEDs on the top of the unit. You can use the LED

19 Low Power ConditionThe access point can be powered from the 48-VDC power module or from an in-line power source. The access point supports the IEEE

2 1 About this GuideThis guide is designed to help you install and minimally configure your Cisco Aironet 1000 Series Lightweight Access Point in a w

20 Note If your access point is connected to in-line power, do not connect the power module to the access point. When powered up, the access point is

21 Ordering DocumentationRegistered Cisco.com users may order Cisco documentation at the Product Documentation Store in the Cisco Marketplace at this

22 To see security advisories, security notices, and security responses as they are updated in real time, you can subscribe to the Product Security In

23 10 Obtaining Technical AssistanceCisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support &a

24 For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in w

25 • Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo merchandise. Visit Cisco Marketplace, the company

26 3. To read translated and localized warranty information about your product, follow these steps:a. Enter this part number in the Warranty Document

27

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

3 General Safety GuidelinesDo not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body

4 WarningDo not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001WarningRead the installation in

5 mode (as opposed to autonomous mode). The access points associate to a controller. The controller manages the configuration, firmware, and control t

6 9. During run-time operations, the controller may issue various commands to the access point via LWAPP control messages. Examples of these commands

7 Before You BeginBefore you begin the installation, review this section to become familiar with the access point’s features and connectors.Access Poi

8 Figure 2 illustrates connectors on the left side of the access point.Figure 2 Access Point Connectors, Left SideFigure 3 illustrates connectors on t

9 Figure 4 illustrates the access point LEDs on the top of the unit.Figure 4 Access Point LEDs5 Installing and Deploying the Access PointThis section