Cisco RPM-XF Spezifikationen Seite 392
- Seite / 688
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
5-182
Cisco ATM Services (AXSM) Configuration Guide and Command Reference for MGX Switches
Release 5.2, Part Number OL-6484-01 Rev. C0, September 2005
Chapter 5
dnallports
dnallports
Down All Ports—de-activates all ports—AXSM
The dnallports command primarily applies to a situation where you want to re-configure resource
partitions or change the choice of service class template (SCT).
Syntax
dnallports
Syntax Description
N o parameters, but the CLI prompts you to confirm the execution.
Related Commands
upallports
Attributes
Example
Check the current state of the logical ports. Down all ports. Up all ports. Re-check the state of the ports.
MGX8850.1.AXSM.a > dspports
ifNum Line Admin Oper. Guaranteed Maximum Port SCT Id ifType VPI
State State Rate Rate (VNNI only)
----- ---- ----- ----- ---------- --------- ----------------- ------ ----------
1 2.1 Up Up 1412830 1412830 5 NNI 0
2 1.2 Up Up 1412830 1412830 2 UNI 0
3 1.1 Up Up 1412830 1412830 5 NNI 0
4 2.2 Up Up 10000 10000 2 UNI 0
MGX8850.1.AXSM.a > dnallports
dnport/dnallports can disrupt traffic on existing connections.
Use this command only to modify partition parameters or change SCT
Do you want to proceed (Yes/No) ? y
WARNING: port is configured as clock source
MGX8850.1.AXSM.a > dspports
ifNum Line Admin Oper. Guaranteed Maximum Port SCT Id ifType VPI
State State Rate Rate (VNNI only)
----- ---- ----- ----- ---------- --------- ----------------- ------ ----------
1 2.1 Down Down 1412830 1412830 5 NNI 0
2 1.2 Down Down 1412830 1412830 2 UNI 0
3 1.1 Down Down 1412830 1412830 5 NNI 0
4 2.2 Down Down 10000 10000 2 UNI 0
MGX8850.1.AXSM.a > upallports
Writing secondary clock, dc=1, line=0
Secondary clock turned on
MGX8850.1.AXSM.a >
Log: yes State: active Privilege: GROUP1
- Switches 1
- CONTENTS 3
- 4 AXSM Card Management 4-1 5
- 5 AXSM Command Reference 5-1 7
- Contents 10
- About This Guide 21
- Conventions 22
- Documentation 22
- Related Documentation 23
- Obtaining Documentation 36
- Documentation Feedback 37
- Submitting a Service Request 38
- Introduction 41
- Command Line Interface 42
- CLI Syntax 43
- AXSM Models 44
- Chapter 1 Introduction 45
- Logical Ports 46
- Common Acronyms 46
- List of Commands by Function 47
- Preparing for Provisioning 57
- AXSM Service Class Templates 63
- Setting Up Lines 65
- Bringing Up Lines 66
- Configuring Lines 68
- LineType 69
- Verifying Line Configuration 70
- Adding Intracard APS Lines 71
- Adding Intercard APS Lines 72
- Table 2-7 Line Channelization 73
- Channelizing a Line 74
- Channelizing a SONET Line 77
- Channelizing an SDH Line 79
- Provisioning ATM Services 83
- • Cisco MGX 8230 84
- • Cisco MGX 8250 84
- • Cisco MGX 8850 (PXM1E) 84
- • Cisco IGX switches 84
- SVC Configuration Quickstart 89
- Adding ATM Ports 109
- Creating an IMA Group 116
- • AXSM: 1–60 125
- • AXSM-E: 1–32 125
- Configuring ILMI on a Port 129
- Configuring PNNI Links 136
- Defining a Feeder Port 140
- AXSM Card Management 149
- Managing CLI Sessions 150
- Managing Cards 151
- Managing Card SCTs 152
- Displaying Card SCT Settings 154
- Managing Port SCTs 157
- Selecting a Port SCT 158
- Changing a Port SCT 158
- Displaying Port SCT Settings 159
- Port SCT ABR Parameters (abr) 178
- Managing Lines 179
- Bringing Down a Line 180
- Managing Ports 181
- Deleting Ports 185
- Delete an ATM Port 186
- Managing Resource Partitions 187
- Managing Connections 192
- Deleting ATM Connections 194
- Rerouting a P2MP Party 196
- Testing ATM Connections 198
- Verifying PNNI Communications 200
- Managing IMA Groups 203
- Configuring IMA Groups 205
- • 1 = IMA version 1.0 206
- • 2 = IMA version 1.1 206
- Configuring an IMA Link 207
- Deleting an IMA Group 208
- Testing an IMA Link 209
- Managing Loopbacks 210
- AXSM Command Reference 211
- APS Overview 212
- APS Architecture Modes 212
- AXSM/A and AXSM/B APS Issues 214
- Syntax Description 214
- Related Commands 215
- Attributes 215
- Before Adding a Connection 218
- Adding a Connection 218
- Traffic Parameters 219
- Service Types, CDV, and CTD 220
- Routing Parameters 221
- Frame Discard 221
- Restrictions 222
- Local-Only Parameters 223
- OAM and Failure Management 225
- Syntax (AXSM) 225
- • 1 = enable 229
- Error Messages 231
- Value 1.3 2 4 3 64 1 275 236
- Setting the Correct Port SCT 238
- Usage Guidelines 241
- Related Command 241
- Syntax Description (AXSM) 243
- -ds3 1.16 244
- AXSM-E, AXSM-XG Dependencies 247
- Using the Correct SCT 250
- Syntax (AXSM-XG) 251
- Example 261
- • AXSM-E : 1–32 270
- • AXSM-XG: 1–126 270
- Examples 278
- Attributes (AXSM) 291
- Attributes (AXSM-E, AXSM-XG) 291
- Display Command History 302
- Configuration successful 305
- Generic Syntax Description 306
- Thresholds for SONET Section 307
- Thresholds for SONET Line 307
- Thresholds for SONET Path 307
- Thresholds for DS3 308
- Thresholds for E3 308
- Thresholds for PLCP 308
- Table 5-15 BERT Test Patterns 318
- Background 322
- Types of Card Statistics 325
- Syntax (SONET) 347
- Syntax Description (SONET) 347
- Syntax (DS3) 347
- Syntax Description (DS3) 348
- Syntax (E1) 349
- Syntax Description (E1) 349
- Syntax (E3) 349
- Syntax Description (E3) 349
- <SEFS24Hr> 351
- Syntax (Sonet Lines) 352
- 15-minute intervals to 500 353
- Chapter 5 354
- <SEFS24>] 359
- Specifying the Core Mask 375
- Redundancy Policy 376
- Aborting a Core Dump 376
- Example (AXSM-E) 388
- Example (AXSM-32-T1E1-E) 388
- AXSM, AXSM-E, AXSM-XG) 400
- Attributes (AXSM-32-T1E1-E) 401
- Example (AXSM) 435
- Example (AXSM-XG) 436
- Syntax (AXSM-E, AXSM-XG) 442
- Example (SCT 2) 443
- Example SCT 3 445
- Step 1 Execute tstdelay 458
- Step 2 Check the results 458
- • ATLAS programmed data 465
- • SABRE programmed data 465
- The dspcons Output on AXSM 472
- Syntax Description 498
- Example 499
- Attributes 500
- alarm type 513
- Syntax (AXSM, AXSM-XG) 523
- Syntax (AXSM-E) 523
- (AXSM-E) 523
- Display Output 523
- Display Lines—AXSM 539
- Version Numbering Conventions 623
- Firmware Filenames 623
- Version Numbers 623
Verwandte Produkte und Handbücher für Vernetzung Cisco RPM-XF
Vernetzung Cisco IAD2431-16FXS Betriebsanweisung
(94 Seiten)
(94 Seiten)
Vernetzung Cisco 2613 Bedienungsanleitung
(16 Seiten)
(16 Seiten)
Vernetzung Cisco NM-HDV-1E1-30E - 30 Enhanced Channel E1 Voice/Fax Network Module Wartungshandbuch
(24 Seiten)
(24 Seiten)
Vernetzung Cisco 15216 EDFA2 Spezifikationen
(252 Seiten)
(252 Seiten)
Vernetzung Cisco EZXS88W Betriebsanweisung
(10 Seiten)
(10 Seiten)
Vernetzung Cisco DPC 3925 Betriebsanweisung
(106 Seiten)
(106 Seiten)
Vernetzung Cisco OL-6900-01 Bedienungsanleitung
(126 Seiten)
(126 Seiten)
Vernetzung Cisco RT31P2-NA Bedienungsanleitung
(73 Seiten)
(73 Seiten)
Vernetzung Cisco 675E Betriebsanweisung
(50 Seiten)
(50 Seiten)
(15 Seiten)
Vernetzung Cisco PXM Version 1.1 Betriebsanweisung
(972 Seiten)
(972 Seiten)
Vernetzung Cisco uBR904 Spezifikationen
(38 Seiten)
(38 Seiten)
Kenwood MFJ-286 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Mikrofone Kenwood MFJ-286.
Wir stellen 1 PDF-Handbücher Kenwood MFJ-286 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Kommentare zu diesen Handbüchern