Cisco WS-X4604-GWY - VoIP Gateway Spezifikationen Seite 151
- Seite / 166
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
A-7
Cisco Catalyst 4000 Access Gateway Module Installation and Configuration Note
OL-3008-01
Appendix A Identifying Hardware Problems with the ROM Monitor
ROM Monitor Commands
at 0x80006590 (fp + 0x24) = 0x00000000
at 0x80006594 (fp + 0x28) = 0x81250000
at 0x80006598 (fp + 0x2c) = 0x00000001
rommon 7 > frame 03
Frame 03:FP = 0x8000665c PC = 0x8002011c
at 0x80006664 (fp + 0x08) = 0x0122ed84
at 0x80006668 (fp + 0x0c) = 0x83ff7800
rommon 8 > frame 04
Frame 04:FP = 0x8000666c PC = 0x80020068
at 0x80006674 (fp + 0x08) = 0x00000002
at 0x80006678 (fp + 0x0c) = 0x00000000
at 0x8000667c (fp + 0x10) = 0x0122ed84
at 0x80006680 (fp + 0x14) = 0x83ff7800
rommon 9 > frame 05
Frame 05:FP = 0x80006684 PC = 0xfff03e7c
at 0x8000668c (fp + 0x08) = 0x00000005
at 0x80006690 (fp + 0x0c) = 0x800046ac
at 0x80006694 (fp + 0x10) = 0xfff24c90
at 0x80006698 (fp + 0x14) = 0x00000000
at 0x8000669c (fp + 0x18) = 0x00000000
at 0x800066a0 (fp + 0x1c) = 0x00000000
at 0x800066a4 (fp + 0x20) = 0x00000000
at 0x800066a8 (fp + 0x24) = 0x00000000
at 0x800066ac (fp + 0x28) = 0x00000000
at 0x800066b0 (fp + 0x2c) = 0x00000000
rommon 10 >
sysret
Enter the sysret command to display return information from the last booted system image. This
information includes the reason for terminating the image, a stack dump of up to eight frames, and, if an
exception is involved, the address where the exception occurred. An example of this command is as
follows:
rommon 8 > sysret
System Return Info:
count: 19, reason: a SegV exception
pc:0x802b1040, error address: 0x802b1040
Stack Trace:
FP: 0x80908398, PC: 0x802b102c
FP: 0x809083b0, PC: 0x802b0b88
FP: 0x809083d8, PC: 0x8017039c
FP: 0x809083e8, PC: 0x8016f764
Cookie Commands
This section lists the ROM cookie and fxs_high_density cookie commands.
cookie
Enter the cookie command to display identification information for the AGM.
In nonprivileged mode, the cookie command displays read-only information for a AGM.
- Cisco Catalyst 4000 1
- Access Gateway Module 1
- CONTENTS 3
- Contents 4
- Audience 9
- Organization 9
- Conventions 10
- Safety Overview 11
- Related Documentation 12
- Obtaining Documentation 13
- Documentation Feedback 14
- Cisco.com 14
- Technical Assistance Center 15
- Overview 17
- IP Telephony Campus 18
- Large Branch Office 18
- • the console port on the AGM 19
- Hardware Features 20
- Cisco Catalyst 4000 DSP Set 21
- Data Interface Modules 21
- Voice Interface Modules 22
- Signaling Support on AGM 23
- Switch-Type Support on AGM 23
- Software Features 24
- Security 25
- Resiliency 25
- Network Management Support 26
- Preparing to Install the AGM 27
- Installing the AGM 29
- Hot-Swapping Features 31
- Checking the AGM Operation 32
- Power Supply 1 34
- Power Supply 2 34
- WAN Interface Modules 35
- SEE MANUAL 36
- INSTALLATION 36
- Straight-through 41
- RJ-11-to-RJ-11 cable 41
- RJ-11 ports 41
- RJ-11 wall jack 41
- RJ-21 Connectors 42
- Velcro strap 43
- ConfigurableNot used 45
- RJ-48S ports 47
- RJ-48S wall jack 47
- RJ-48C ports 48
- NT1 device 48
- RJ-45-to-RJ-45 cable 48
- S/T port 48
- RJ-48C-to-RJ-48C cable 50
- RJ-48C wall jack 50
- Booting the AGM 53
- Accessing the AGM 54
- Configuring the Console Port 55
- Connecting a Terminal 56
- Connecting a Modem 56
- Using the Cisco IOS CLI 57
- Getting Help 58
- Command Modes 58
- Gateway(config-if)# 59
- (config 59
- Gateway(config-dial-peer)# 59
- Saving Configuration Changes 60
- Table 4-2 ISDN Switch Types 68
- Configuring T1 Interfaces 69
- Configuring E1 Interfaces 71
- Preparing to Configure VoIP 75
- Configuring Voice Interfaces 76
- MGCP Configuration 77
- Enabling MGCP 78
- • E&M Wink Start 81
- • E&M Delay Start 81
- H.323 Gateway Configuration 86
- FXS Emulation Example 90
- FXO Emulation Example 90
- E&M Emulation Example 91
- Configuring ISDN BRI Lines 92
- Gateway 1 Configuration 95
- T1/E1 Configuration (H.323) 96
- T1/PRI Configuration Example 97
- E1/PRI Configuration Example 98
- Configuration for AGM AGLB-1 99
- Configuration for AGM AGLB-2 100
- FXO Connection to PSTN 101
- San Jose Salt Lake City 102
- AGM SLC Configuration 103
- OL-3008-01 104
- Configuring FXS Voice Ports 106
- Validating the Configuration 107
- Fine-Tuning FXS Voice Ports 108
- Activating the Voice Port 110
- Sample Configuration 110
- Verifying the Configuration 120
- Sample Configurations 121
- Configuration File for Peer 1 124
- Configuration File for Peer 2 126
- Configuring the DSP Farm 129
- IP Telephony Gateway Mode 130
- Conferencing Service 131
- Transcoding Service 132
- Troubleshooting the AGM 137
- Troubleshooting Controller 138
- Troubleshooting Hardware 141
- Troubleshooting TDM 141
- Troubleshooting DSP 142
- SIMM 3 DSP 12–17 143
- SIMM 4 DSP 18–23 143
- Entering ROM Monitor Mode 145
- Configuring for Autoboot 146
- ROM Monitor Commands 147
- Debugging Commands 150
- Cookie Commands 151
- Upgrading the ROM Monitor 157
- Using Loss Plan Defaults 159
- Transmission Loss Plan 160
- Console Connector Pinouts 161
- Management Port Pinouts 161
- Identifying a Rollover Cable 163
- Connecting to a PC 164
- Connecting to a Terminal 164
Verwandte Produkte und Handbücher für Gateways / Controller Cisco WS-X4604-GWY - VoIP Gateway
(14 Seiten)
(90 Seiten)
(25 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern