Cisco 6400 Einstellungsanleitung Seite 51
- Seite / 198
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
C H A P T E R
3-1
Cisco 6400 Software Setup Guide
OL-1183-04
3
Basic NRP Configuration
This chapter describes how to perform a basic configuration for the node route processors (NRP-1,
NRP-2, and NRP-2SV). The Cisco6400 can contain multiple NRP modules, configured to operate
independently or as 1+1 redundant pairs (NRP-1 only at this time). This chapter contains the following
sections:
• NRP-1 Configuration, page 3-1
• NRP-2 and NRP-2SV Configuration, page 3-7
• Transferring an NRP-1 Configuration to an NRP-2 or NRP-2SV, page 3-20
• Permanent Virtual Circuits, page 3-20
For information on differences among the NRP types, see the release notes for your specific software
images. Also see Table1-1 on page1-4.
NRP-1 Configuration
This section describes configuration information specific to the NRP-1, including:
• Methods Available for Configuring the NRP-1 , page 3-1
• Initial NRP-1 Configuration, page 3-2
• Segmentation and Reassembly Buffer Management, page 3-5
• Using the NRP-1 File Systems and Memory Devices, page 3-6
Methods Available for Configuring the NRP-1
The following methods are available for configuring the NRP-1:
• From a local console or workstation—Connect to the console port of the NRP-1.
• From a remote console or workstation—Initiate a Telnet connection to the NRP-1 over the NME
interface.
• From the Cisco 6400 Service Connection Manager—See theCisco 6400 SCM documentation.
For general information on basic Cisco IOS configuration, see the Cisco IOS Configuration
Fundamentals Configuration Guide.
- Text Part Number: OL-1183-04 1
- Contents 10
- OL-1183-04 10
- Document Objectives 11
- Related Documentation 11
- Audience 12
- Organization 12
- Conventions 13
- Obtaining Documentation 14
- Documentation CD-ROM 15
- Ordering Documentation 15
- Documentation Feedback 15
- Cisco.com 16
- Technical Assistance Center 16
- Product Overview 19
- Cisco 6400 System 20
- Node Switch Processor 21
- Node Route Processor 21
- Node Line Card 23
- Basic NSP Configuration 25
- Verifying DHCP 27
- ATM Address 28
- Verifying the ATM Address 30
- Internal Cross-Connections 34
- Example—Internal PVC 35
- Example—Internal PVP 36
- Network Clocking 38
- Network Routing 42
- NRP-2 and NRP-2SV Support 43
- System Logging 45
- Console and Telnet Access 45
- SNMPv3 Proxy Forwarder 46
- Storing the NSP Configuration 47
- Example—Disk0: versus Slot0: 49
- Basic NRP Configuration 51
- Initial NRP-1 Configuration 52
- Configuring the NRP-1 53
- Setting the I/O Memory Size 56
- Restrictions 58
- Example—Main ATM Interface 61
- Example—ATM Subinterface 61
- Changing the MTU on the NRP-2 62
- PAM mailbox serial interface: 68
- Permanent Virtual Circuits 70
- Configuring VC Classes 74
- Configuring PVC Discovery 76
- Verifying PVC Discovery 78
- Verifying PVC Traffic Shaping 79
- NLC Interface Identification 81
- Autoconfiguration 82
- ATM Interface Types 83
- Configuring UNIs 84
- Network-to-Network Interfaces 85
- Verifying NNI Configuration 86
- Configuring IISP Interfaces 87
- NLC Interface Clocking 88
- DS3 NLC Interface Options 90
- Memory Requirements 94
- NSP Redundancy 95
- Synchronizing Redundant NSPs 96
- PCMCIA Disk Mirroring 97
- Verifying Blind Copying 101
- Example—Disk Synchronization 102
- Examples 103
- NRP Redundancy 107
- Verifying NRP Redundancy 108
- NLC Redundancy 109
- Verifying NLC Redundancy 110
- Verifying SONET APS 112
- • Remote Monitoring, page 6-4 117
- • Alarms, page 6-4 117
- Remote Monitoring 120
- Verifying Temperature Alarms 121
- Clearing Alarms 122
- Web Console 123
- Web Console Installation 124
- Using the Web Console 126
- AppendixA Web Console 127
- FigureA-1 Update Page 128
- Accessing the Web Console 129
- Navigating in Web Console 131
- System Reload Options 134
- Configuring Redundancy 135
- IP Address Management 136
- Setting Static Routes 137
- SNMP Management 138
- Entering System Options 139
- Entering Community Strings 140
- Adding Trap Managers 140
- NRP Status 141
- Subscriber Management 141
- Step 2 Click Remove 143
- System Status 144
- FigureA-13 System Status 145
- Loading New Web Console Pages 146
- Recommendations 147
- Reload the Secondary NRP-1 156
- Reloading the Secondary NRP-1 159
- 2. Reload the Secondary NSP 160
- Prerequisites 161
- Reload the Secondary NSP 161
- Reloading the Secondary NSP 164
- Verifying VCI Values 169
- Shrinking ITT Blocks 172
- Displaying ITT Allocation 172
- GLOSSARY 175
- Glossary 176
Verwandte Produkte und Handbücher für Sicherheitskameras Cisco 6400
(55 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern