Cisco Catalyst 7500 Series Spezifikationen Seite 183
- Seite / 303
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
CHAPTER
5-1
Cisco 7500 Series Installation and Configuration Guide
OL-5008-03 B0
5
Maintaining Your Cisco 7505 Router
Your Cisco 7505 router is configured to your order and is ready for installation and startup when it leaves
the factory. After you install and configure your Cisco 7505 router, you might have to perform specific
maintenance procedures and operations to ensure that the router is operating properly, to upgrade
specific system components, or to replace components with spare parts or field-replaceable units
(FRUs). This chapter describes maintenance operations required to maintain your Cisco 7505 router; it
includes procedures for installing, adding, and replacing internal router components and replaceable
spare parts.
Note Detailed, up-to-date instructions (called configuration notes) are available on Cisco.com.
The replaceable system components fall into two categories: those that support online insertion and
removal (OIR) and those that do not (requiring you to turn off the system power before replacement).
For example, you can remove interface processors and replace them while the system is operating;
however, you must shut down the system power before removing the RSP and the single power supply
in a Cisco 7505 with one power supply installed, or before accessing the chassis interior for any other
reason.
This chapter contains specific component replacement instructions for upgrading, removing, or
replacing the following components:
• Front panel
• Fan tray
• Chassis interface (CI) board
• Power supply
Caution To help prevent problems, before performing any procedures in this chapter, review the “Safety
Recommendations” section on page 2-2.
Note Interface processor-specific configuration information is included in the companion Interface Processor
Installation and Configuration Guide, which shipped with your Cisco 7505 router, as well as in the
individual configuration notes that shipped with your spare interface processors.
- Configuration Guide 1
- CONTENTS 3
- Contents 10
- OL-5008-03 B0 10
- Audience 11
- Organization 11
- Related Documentation 12
- Conventions 13
- Safety Warnings 15
- Attention 16
- Figyelem! 16
- Avvertenza 16
- Advarsel 17
- ¡Advertencia! 17
- Varning! 17
- Restricted Area Warning 18
- Obtaining Documentation 19
- Documentation Feedback 20
- Submitting a Service Request 21
- Terms and Acronyms 24
- Cisco 7505 Overview 25
- Cisco 7505 CyBus Backplane 26
- Cisco 7505 Overview 27
- Cisco 7507 Overview 28
- Cisco 7507 Overview 29
- Cisco 7507-MX Overview 33
- Cisco 7507-MX Overview 34
- Cisco 7513 Overview 37
- Front-panel 38
- Cisco 7513 Overview 39
- 012345RSPRSP89101112 40
- Cisco 7513-MX Overview 42
- Cisco 7513-MX Overview 44
- Cisco 7576 Overview 47
- Cisco 7576 Overview 49
- Router A 50
- Router B 50
- CyBus Slot Number Assignments 51
- RSP2—Cisco 7505 53
- Common RSP Hardware Features 64
- RSP NVRAM 65
- RSP Flash Memory 65
- RSP SRAM 65
- RSP EEPROM 66
- RSP Auxiliary Port Pinout 67
- Arbiter Overview 72
- Chassis Interface Overview 72
- Cisco 7505 Fan Tray Assembly 74
- Cisco 7576) 75
- Interface Processor Overview 76
- System Software Overview 78
- Preparing for Installation 79
- Safety Recommendations 80
- Chassis Lifting Guidelines 81
- Safety Recommendations 82
- Plant Wiring Guidelines 88
- Plant Wiring Guidelines 89
- Top view of router 91
- Front of 92
- Power supplies 93
- Card cage 93
- System blower 93
- Intake air Exhaust air 93
- Noninterface processor end 95
- Interface processor end 95
- Cisco 7500 Series 100
- 7507-MX) 103
- Installing the Cisco 7505 118
- Installing the Cisco 7505 119
- Remove a module as follows: 120
- Install a module as follows: 120
- Rack-Mounting the Cisco7505 121
- Install the cable management 123
- Captive installation screws 131
- Cisco 7513 and Cisco 7576 134
- Unpacking Instructions 134
- Captive screws 142
- Power Supplies 143
- What Do I Do Now? 147
- What Do I Do Now? 148
- Recovering a Lost Password 157
- Configuring Interfaces 163
- Checking the Settings 167
- Copying Files to Flash Memory 173
- Removing/replacing 187
- Chassis interface 193
- Standoff 193
- AC receptacle 195
- On/off switch 195
- Cable retention 195
- DC OK LED 195
- Cisco 7507-MX 201
- AC POWER 203
- Guide tab slides up 207
- • LED board (MAS-7KLED=) 209
- Black (ground) 215
- Purple (+24V) 215
- Blower power connection 215
- Backplane 215
- Cisco 7576 Router 219
- Cisco7576 220
- Cage Assembly 223
- Exchanging the EEPROM Devices 225
- Blower module 228
- Chassis Cover Panels 229
- Backplane Maintenance Cover 231
- 7513-MX, and Cisco7576 232
- Troubleshooting Overview 240
- Cisco 7513-MX, and Cisco7576 250
- Subsystem 253
- Troubleshooting the RSP 256
- Using the RSP LEDs 259
- Using the Power Supply LEDs 261
- For the DC-input 264
- Removing RSP2 SIMMs 267
- Installing New RSP2 SIMMs 268
- Removing RSP4 and RSP8 DIMMs 273
- Configuration Bit Meanings 277
- Bits 0–3 278
- Configuration Bit Meanings 279
- Bit 10 and Bit 14 280
- Bit 11 and Bit 12 280
- Numerics 285
Kenwood MFJ-286 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Mikrofone Kenwood MFJ-286.
Wir stellen 1 PDF-Handbücher Kenwood MFJ-286 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Kommentare zu diesen Handbüchern