Cisco 6260 Installationsanleitung Seite 60
- Seite / 244
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1-42
Cisco 6260 Hardware Installation Guide
OL-2365-02
Chapter 1 Product Overview
Cisco 6260 System Overview
Figure 1-19 E3 I/O Module
Note For hardware specifications for the E3 I/O module, see the “I/O Module” section on page A-11.
1.2.4.2 E1 I/O Module Overview
The E1 I/O module provides eight E1 interfaces that can be allocated as either individual E1 network
trunk or subtend interfaces, or as IMA group trunk or subtend interfaces. The E1 I/O module also
provides the alarm pinouts and BITS clock input circuits for the Cisco 6260 system.
The E1 I/O module works with the DS3+T1/E1 IMA NI-2 card in the Cisco 6260 chassis.
Figure 1-20 shows a close-up of the E1 I/O module.
44751
PEM 1/PEM 2
AUD_CRIT/AUD_MAJ
AUD_MIN/VIS_CRIT
VIS_MAJ/VIS_MIN
STAT_ALARMS
BITS_A/BITS_B
60V
0.5 A MAX
L
O
G
IC
IN
P
U
T
S
B
IT
S
C
L
O
C
K
RX
TX
P1
RX
TX
P2
RX
TX
P3
1
3
2
1
E3 75-ohm coaxial BNC connectors. The P1
RX and TX connectors serve as the network
trunk interface. 3
Six rows of six wire-wrap pins that support
CO alarm relay interfaces and BITS clock
input circuits.
2
E3 75-ohm coaxial BNC connectors. The P2
and P3 RX and TX connectors serve as
subtend connectors to additional chassis.
- Text Part Number: OL-2365-02 1
- CONTENTS 3
- Contents 4
- 5 Troubleshooting 5-1 6
- OL-2365-02 10
- Audience 13
- Organization 13
- Conventions 14
- Related Documentation 15
- Obtaining Documentation 16
- Cisco.com 17
- Technical Assistance Center 17
- Contacting TAC by Telephone 18
- Product Overview 19
- 1.1.1 Features 21
- 1.1.2 Configurations 21
- 1.1.2.3 IMA Configuration 22
- Subtending host 27
- Cisco 6260 System Overview 28
- 1.2.2 Cisco 6260 Connectors 30
- 1.2.3 Cisco 6260 Cards 31
- 1.2.3.1.1 Faceplate Features 32
- 1.2.3.2.1 Faceplate Features 34
- 1.2.3.3.1 Faceplate Features 36
- 1.2.3.4.1 Faceplate Features 38
- 1.2.3.5.1 Faceplate Features 40
- 1.2.3.6.1 Faceplate Features 42
- 1.2.3.7.1 Faceplate Features 44
- NI2-155MM-155MM2 Only 47
- 1.2.3.9.1 Faceplate Features 49
- 1.2.3.13 Redundancy Overview 57
- 1.2.4 Cisco 6260 I/O Modules 59
- Figure 1-19 E3 I/O Module 60
- Figure 1-20 E3 I/O Module 61
- Figure 1-21 OC-3c I/O Module 61
- 1.2.5 PEM 63
- Figure 1-23 PEM Faceplate 64
- 1.2.6 Fan Tray 65
- 1.2.8 ESD Jack 66
- 1.2.7 Air Filters 66
- 1.3 Management Software 67
- Management Software 68
- Preparing for Installation 69
- 2.1.2 Warning Definition 70
- Safety Requirements 71
- 2.1.4.1 Hot Swapping Cards 78
- 2.2 Site Requirements 79
- 2.2.1.2 Ventilation 80
- 2.2.1.3 Space 81
- 2.2.2 Power Requirements 82
- Site Requirements 83
- Required Tools and Equipment 84
- 2.5 Verifying Contents 86
- 2.6 Inspecting for Damage 86
- Inspecting for Damage 87
- 3.1 Installation Checklist 90
- 3.2 Installation Procedures 91
- 3.2.6 Ground the Cisco 6260 95
- Negative connection (–) 101
- Positive connection (+) 101
- Ground connection ( ) 101
- 3.2.12 Apply Power 102
- –48V on the voltmeter 103
- Installation Procedures 108
- 3.2.19.1 Before You Begin 110
- Splitter Configuration 117
- 4.1 Installation Checklist 118
- 4.2 Installation Procedures 118
- Bracket orientation for 120
- ETS 600-mm rack 120
- Bracket orientation 120
- Cisco 6260 122
- 4.2.5 Ground the Cisco 6260 123
- 0.43 in 126
- 4.2.9 Apply Power 129
- 4.2.16.1 Before You Begin 137
- Troubleshooting 145
- 5.2 Basic Checks 146
- 5.4 System-Wide Problems 147
- OL-2365-01 148
- System-Wide Problems 148
- 5.5 FRU-Specific Problems 152
- FRU-Specific Problems 153
- 5.5.3 Line Card Problems 154
- 5.5.4 I/O Module Problems 158
- 5.5.5 Fan Tray Problems 159
- 5.5.6 PEM Problems 160
- 5.6 Alarms 161
- Table 5-17 IMA Group Alarms 164
- Table 5-20 Power Alarms 165
- Cisco 6260 System 167
- 6.2 Fan Tray Maintenance 168
- Fan Tray Maintenance 170
- 6.3.1 xTU-C Line Card 173
- Unlocked 174
- 6.3.2 DS3/2DS3 NI-2 Card 175
- 6.3.4 OC-3c/OC-3c NI-2 Card 181
- 6.3.5 I/O Module 183
- 6.3.6 PEM 186
- 6.3.6.2 Removing the PEM 188
- Technical Specifications 189
- A.1.1 Cisco 6260 Chassis 190
- Hardware Specifications 192
- A.1.9 DS3/2DS3 NI-2 Card 196
- A.1.12 I/O Module 199
- A.1.13 PEM 199
- A.2 Software Specifications 200
- Port Mapping Specifications 201
- Port Mapping Table 202
- Standard Telco Color Chart 206
- C.1 xDSL Connectors 209
- C.2 I/O Module Connectors 209
- • BITS clock input circuits 211
- RJ-45 female 212
- C.5 Ethernet Port 213
- Ethernet Port 214
- Numerics 215
- Glossary 216
Verwandte Produkte und Handbücher für Vernetzung Cisco 6260
Vernetzung Cisco 815 Spezifikationen
(28 Seiten)
(28 Seiten)
Vernetzung Cisco WES610N Bedienungsanleitung
(21 Seiten)
(21 Seiten)
Vernetzung Cisco 510 Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Vernetzung Cisco WPC54GS Betriebsanweisung
(83 Seiten)
(83 Seiten)
Vernetzung Cisco 10700 Betriebsanweisung
(602 Seiten)
(602 Seiten)
Vernetzung Cisco ME 3800X Spezifikationen
(622 Seiten)
(622 Seiten)
Vernetzung Cisco Aironet 340 Series Spezifikationen
(362 Seiten)
(362 Seiten)
Vernetzung Cisco 867W Bedienungsanleitung
(59 Seiten)
(59 Seiten)
Vernetzung Cisco 7400 series Betriebsanweisung
(12 Seiten)
(12 Seiten)
Vernetzung Cisco 7576 Bedienungsanleitung
(26 Seiten)
(26 Seiten)
Vernetzung Cisco WRT610N Bedienungsanleitung
(3 Seiten)
(3 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern