Cisco 1417 - 1417 Router - EN Bedienungsanleitung

Table of ContentsDSL Modem/Router Interface Pinouts and Status LED Descriptions...1Document ID:

Note: In certain circumstances in which the Cisco 676 operates correctly, the WAN LNK LED appears offwhen the PWR/ALARM LED is on. For example, this c

WANACTYellowBlinking when the xDSL port receives ortransmits data.Cisco 678The ADSL port uses an RJ−11 connector.ADSL Port PinoutsPinSignal3Ring4TipNo

IDSL RJ−45 Port PinoutsPinFunction4IDSL (Tip)5IDSL (Ring)Note: Pins 1, 2, 3, 6, 7,and 8 are not used.Power/LinkLEDs To Check Normal PatternsPowerOK On

and when the router completes theself−test procedure and begins tooperate.PHONE 1, 2,3, 4GreenOn when basic telephone service is inuse. Blinks during

Cisco 828xDSL Port PinoutsThe RJ−11 connector provides xDSL connection to external media through a standard RJ−11 6−pin modularjack.PinDescription3XDS

4XDSL_RingNote: Pins 1, 2, 5, and 6 are not used.LED DescriptionsLEDColor FunctionOK LEDGreenOn when power is supplied to the routerand when the route

operate.G.SHDSL CDGreenOn when the G.SHDSL device isphysically connected. Blinks when theconnection has a problem.G.SHDSLRXDGreenBlinks when a G.SHDSL

2RD − < −−− > 8 TD −Note: Pins 3, 4, 5, and 6 are not used.Front−Panel LED DescriptionsFunction LEDColorDescriptionSystemPWRGreenOn when DC powe

3<−−−> 34<−−−> 45<−−−> 5Note: Pins 1 and 6 are not used. Pins 2 and 5 are used for data.POTS Crossover CableThe purple (with a blue

equipment at the service provider office(Cisco 1417 Router).ACTGreenBlinks when data is sent to or receivedfrom the ATM−25 port (Cisco 1401Router) or

Table of ContentsDSL Modem/Router Interface Pinouts and Status LED Descriptions xDSL Port Pinouts...

network.Verify that the CD LED goes on.This indicates that the card is connected to the network.5. NetPro Discussion Forums − Featured ConversationsNe

DSL Modem/Router Interface Pinouts and StatusLED DescriptionsDocument ID: 15108IntroductionPrerequisites Requirements Components Used C

Cisco SOHO78 xDSL Port Pinouts LED DescriptionsCisco 1401 ATM−25 Cable ATM Loopback Plug Front−Panel LED DescriptionsCisco 14

Cisco 605The Asymmetric Digital Subscriber Line (ADSL) port uses an RJ−11 connector.ADSL Port PinoutsPinSignal3Ring4TipRear Panel LEDsLEDFunction Desc

Note: In certain circumstances in which the Cisco 626 operates correctly, the WAN LNK light appears offwhen the PWR/ALARM light is on. For example, th

If the WAN LNK LED turns off after the Cisco 627 has been transferring data, the Cisco 627 or the Cisco6100/6200 has the SESSION timeout set. If the t

If the WAN LNK LED does not turn on when you power up the modem:Wait approximately fifteen seconds.1. Check all cabling and connections.2. Turn off th

WAN LNKWAN LinkBlinks during ADSL line trainingactivities. When the light blinksseveral times and then stops, thecentral office equipment isunavailabl