Cisco IGX 8400 Series Bedienungsanleitung PDF herunterladen

Cisco MC3810–IGX 8400 Interworking MOD-1

Cisco MC3810–IGX 8400

Interworking

Feature Summary

Using the Cisco MC3810–IGX 8400 Interworking functionality, you can conﬁgure the

Cisco MC3810 multiservice access concentrator to act as an access device to the IGX 8400 switch.

On the Cisco MC3810, a frame trunk card (FTC) trunk port is conﬁgured to send trafﬁc to the IGX

frame trunk module (FTM) port using the network management system (NMS) protocol. Using IGX

Interworking, you can scale large networks of Cisco MC3810 concentrators to IGX 8400 switches.

Note This feature module provides only conﬁguration information for the Cisco MC3810. For

information about IGX switch conﬁguration and commands, see the Cisco WAN Switching

Command Reference for version 9.1.

Beneﬁts

Cisco MC3810–IGX 8400 Interworking provides the following beneﬁts:

• Enables the scaling of large networks of Cisco MC3810 concentrators to IGX 8400 switches.

• Provides central site solutions that minimize equipment costs, simplify network conﬁguration,

and provide end-to-end quality of service and prioritization.

• Unlike other vendors, whose products require multiple Frame Relay Access Devices (FRADs) at

a central site to de-couple voice and data, the Cisco MC3810–IGX 8400 Interworking solution

allows you to terminate voice and data directly on the switch. This minimizes central site

management costs by eliminating extra cabling, equipment, and space requirements.

Lists of Terms

CVM–Channelized voice module on the Cisco 8400 IGX switch.

FRAD–Frame Relay Access Device.

FTC trunk–Frame trunk card (FTC) channel is the channel between the Cisco MC8310 and the

IGX 8400 switch.

FTM–Frame Trunk Module on the Cisco 8400 IGX switch.

FTM protocol–The FTM protocol is the name given to the framing and information exchange

protocols used between the Cisco MC3810 and the FTM card in the IGX. The frames are

standards-based on the outside (Data-Link Control Identiﬁer, CRC), but use a proprietary

encapsulation inside.

1 2 3 4 5 6 ... 21 22

Inhaltsverzeichnis

Seite 1 - Interworking

Cisco MC3810–IGX 8400 Interworking MOD-1Cisco MC3810–IGX 8400InterworkingFeature SummaryUsing the Cisco MC3810–IGX 8400 Interworking functionality, y

Seite 2 - Platforms

RestrictionsMOD-10Release 12.0(1)XAConﬁguration on Cisco MC3810 No. 1hostname router19network-clock base-rate 56kip subnet-zerocontroller T1 0 framing

Seite 3

Configuration on Cisco MC3810 No. 1 Cisco MC3810–IGX 8400 Interworking MOD-11 frame-relay map ip 10.10.11.51 103 frame-relay map ip 10.10.12.2 103 fra

Seite 4

RestrictionsMOD-12Release 12.0(1)XA port 1/6dial-peer voice 4000 vofr destination-pattern 4... session target Serial0:0 40Conﬁguration on Cisco MC3810

Seite 5 - (Optional)

Configuration on Cisco MC3810 No. 2 Cisco MC3810–IGX 8400 Interworking MOD-13interface Serial0:0 no ip address no ip directed-broadcast encapsulation

Seite 6

RestrictionsMOD-14Release 12.0(1)XAdial-peer voice 2 pots destination-pattern 4002 port 1/2dial-peer voice 3 pots destination-pattern 4003 port 1/3dia

Seite 7

connect Cisco MC3810–IGX 8400 Interworking MOD-15connectTo conﬁgure a data connection on the Cisco MC3810 to an IGX switch that will travel over the F

Seite 8

connect voiceMOD-16Release 12.0(1)XAconnect voiceTo conﬁgure a connection on the Cisco MC3810 between a voice dial peer and the FTC trunk, usethe conn

Seite 9 - Conﬁguration Example

encapsulation ftc-trunk Cisco MC3810–IGX 8400 Interworking MOD-17encapsulation ftc-trunkTo enable FTC trunk encapsulation on a serial interface on the

Seite 10 - Release 12.0(1)XA

ftc-trunk frame-relay-dlciMOD-18Release 12.0(1)XAftc-trunk frame-relay-dlciTo map the FTC Frame Relay DLCI to an existing Frame Relay DLCI for data tr

Seite 11

ftc-trunk management-dlci Cisco MC3810–IGX 8400 Interworking MOD-19ftc-trunk management-dlciTo map the FTC management DLCI to an existing Frame Relay

Seite 12

RestrictionsMOD-2Release 12.0(1)XAUVM–Universal voice module on the Cisco 8400 IGX switch.RestrictionsThe following restrictions and limitations apply

Seite 13

ftc-trunk management-protocolMOD-20Release 12.0(1)XAftc-trunk management-protocolTo select the mode on the Cisco MC3810 that management frames are sen

Seite 14 - Command Reference

ftc-trunk voice-dlci Cisco MC3810–IGX 8400 Interworking MOD-21ftc-trunk voice-dlciTo map the FTC voice DLCI to an existing Frame Relay DLCI for voice

Seite 15 - Usage Guidelines

ftc-trunk voice-dlciMOD-22Release 12.0(1)XA

Seite 16

Configuring the Cisco MC3810 FTC Management DLCI Cisco MC3810–IGX 8400 Interworking MOD-3This section assumes that you have already conﬁgured the foll

Seite 17

RestrictionsMOD-4Release 12.0(1)XAYou have a choice of how to proceed from here. Choose one of the following options:• To conﬁgure data connections ov

Seite 18

Configuring the Cisco MC3810 FTC Frame Relay DLCI for Data Traffic (Optional) Cisco MC3810–IGX 8400 Interworking MOD-5Conﬁguring the FTC Management DL

Seite 19

RestrictionsMOD-6Release 12.0(1)XAAfter the Frame Relay FTC DLCI is conﬁgured, you can now establish connections over the FTCtrunk. For more informati

Seite 20

Configuring the Cisco MC3810 FTC Frame Relay DLCI for Data Traffic (Optional) Cisco MC3810–IGX 8400 Interworking MOD-7Conﬁguring the Cisco MC3810 IP R

Seite 21

RestrictionsMOD-8Release 12.0(1)XAConﬁguring the Cisco MC3810 FTC Voice DLCI for Voice Connections(Optional)In addition to the FTC management DLCI, yo

Seite 22

Configuring the Cisco MC3810 FTC Voice DLCI for Voice Connections (Optional) Cisco MC3810–IGX 8400 Interworking MOD-9Conﬁguring the Voice Channels on