Cisco 2600XM Series Bedienungsanleitung

Quick Start GuideCisco 2600XM Series and Cisco 2612 RoutersINCLUDING LICENSE AND WARRANTY1 Cisco 90-Day Limited Hardware Warranty Terms2 Documents, Eq

10The brackets for 19-, 23-, and 24-inch racks are shown in Figure 1.Figure 1 Brackets for Rack-Mounting of Routers with 1-RU Chassis HeightAttaching

11Figure 4 Bracket Installation for Rear Mounting in 19-Inch RackFigure 5 Bracket Installation for Rear Mounting: 19-Inch Rack with 17.75-Inch Opening

12Figure 7 Bracket Installation for Center Mounting with Rear Panel Forward: 19-, 23-, or 24-Inch RackFigure 8 Bracket Installation for Center Mountin

13Figure 9 Attaching the Brackets for Wall-MountingAttaching to WallAttach the chassis to the wall:• Position the end nearest the power cable at the t

14Step 3 Attach the ground lug or ring terminal to the chassis as shown in Figure 10 or Figure 11. For the ground lug, use thetwo screws with captive

15Power ConnectionsWarningRead the installation instructions before connecting the system to the power source. Statement 1004Note The installation mus

16Wiring Procedure for Nominal 48 VDC InputTo connect the router to a DC power source, perform this procedure:Step 1 Remove power from the DC circuit.

17Step 4 Secure the wires using cable ties.Step 5 Turn on power to the DC circuit.Connecting Routers to the Cisco Redundant Power SystemIf your router

185 Power Up the RouterChecklist for Power-UpYou are ready to power up the Cisco router after you have completed the following steps:• Chassis is secu

19You may see different startup messages:• If you see the following messages, the router has booted with a configuration file and is ready for initial

21 Cisco 90-Day Limited Hardware Warranty TermsThere are special terms applicable to your hardware warranty and various services that you can use duri

20Initial Configuration Using Cisco Router and Security Device ManagerIf the following messages appear at the end of the startup sequence, Cisco Route

21Step 3 Enter a host name for the router (this example uses 2610):Configuring global parameters:Enter host name [Router]: 2610Step 4 Enter an enable

22Step 11 The configuration appears:The following configuration command script was created:hostname 2610enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1

23For interface numbering information, see the “Interface Numbering” section on page 23.Step 1 To proceed with manual configuration using the CLI, ent

24• First built-in Ethernet interface—Ethernet 0/0• Second built-in Ethernet interface—Ethernet 0/1, or optionally in Cisco 2612 and Cisco 2613 only:

25To access documentation using Cisco Connection Online (CCO):For Cisco 2600XM series platform documentation, start on Cisco.com at http://www.cisco.c

2611 Obtaining Technical AssistanceFor all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Su

2712 Obtaining Additional Publications and InformationInformation about Cisco products, technologies, and network solutions is available from various

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

32 Documents, Equipment, and ToolsUser DocumentationAll the documents referenced in this quick start guide are available online on Cisco.com. To be su

4Warning DefinitionWarningIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before

5AvvertenzaIMPORTANTI ISTRUZIONI SULLA SICUREZZAQuestosimbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone.

6AvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇAEste símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesõescorporais.

7AdvarselVIGTIGE SIKKERHEDSANVISNINGERDette advarselssymbol betyder fare. Dubefinder dig i en situation med risiko forlegemesbeskadigelse.Før du begyn

8WarningThis unit is intended for installation in restricted access areas. A restricted access area can be accessed onlythrough the use of a special t

9WarningTo avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage(TNV) circuits. LAN ports contain