Cisco MC3810 Spezifikationen Seite 81
- Seite / 107
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Application View Optional Applications
Device Management Page 81 Cisco MC3810
Polling Interval
A read-write value giving the number of seconds
between successive state enquiry messages. The
default value is 10.
Enquiry Interval
A read-write value for the number of status
enquiry intervals that pass before a full status
enquiry message is issued. The default value is 6.
Error Threshold
A read-write value for the maximum number of
unanswered status enquiries the equipment will
accept before declaring the interface down. The
default value is 3.
Monitored Events
A read-write value for the number of status
polling intervals over which the error threshold is
counted. For example, if within this value the
station receives the Error Threshold number of
errors, the interface is marked as down. The
default value is 4.
Max Supported VCs
A read-write value for the maximum number of
VCs allowed for this interface. This is usually
dictated by the Frame Relay network. In response
to a SET, if a value less than zero or higher than
the agent’s maximum capability is configured, the
agent should respond with “bad Value.”
Multicast
Indicates whether the Frame Relay interface is
using a multicast service. The possible values are
nonBroadcast and broadcast.
Frame Relay Error Table
Access: From the Icon Subviews menu for the
CiscoFRApp, select Error Table.
Index
A value that identifies a table entry.
Error Type
The type of error that was last seen on the
interface. The possible values are unknownError,
receiveShort, receiveLong, illegalDLCI,
unknownDLCI, dlcmiProtoErr, dlcmiUnknownIE,
dlcmiSequenceErr, dlcmiUnknownRpt, and
noErrorSinceReset.
Error Data
An octet string containing as much of the error
packet as possible (at least up to the PDU). As a
minimum, it contains the Q922 address or as
much as was delivered.
Error Time
The value of sysUpTime when the error was
detected.
- Cisco MC3810 1
- October 2001 Aprisma 2
- Contents 3
- Contents Contents 4
- Introduction 6
- Supported Devices 7
- The SPECTRUM Model 7
- Option Accesses the 8
- CiscoView 12
- Device View 14
- Interface Icons 15
- Interface Icon Subviews Menu 16
- Information View 17
- Interface Status View 17
- Interface Configuration 17
- Secondary Address Panel View 18
- Device Topology View 19
- Application View 20
- Supported Applications 21
- Device-Specific MIBs 22
- Generic Routing Applications 23
- RTMP Table View 24
- ZIP Table View 26
- ATPORT Table View 28
- ARP Table View 29
- AppleTalk Echo View 29
- DECnet Routing Application 30
- Interface Cost Table View 31
- DECnet Routing Level 1 View 31
- DECnet Routing Level 2 View 31
- DECnet Routing Hello View 31
- IP Routing Application 32
- BGP4 Application 33
- Path Attribute Table 35
- Novell Routing Application 36
- Check Point Information 37
- IPX Accounting Information 37
- Check Point Accounting Table 37
- Vines Routing Application 38
- Vines Routing ICP View 39
- Vines Broadcast Detail View 39
- Vines Rx View 40
- XNS Routing Application 41
- Cisco BSTUN Application 42
- BSTUN Ports View 43
- BSTUN Routes View 43
- Cisco STUN Application 44
- STUN Port View 45
- STUN Route View 45
- Optional Applications 46
- Cisco Chassis Application 47
- ROM Information 48
- RAM Information 48
- Cisco Modem Application 49
- Modem Line Status Table View 50
- State Meaning 51
- Reason Code Meaning 52
- Configuration Table 54
- Cisco Flash Application 58
- Flash Directory 59
- Table View 61
- Cisco Ping Application 62
- Cisco Queue Application 64
- Queue Statistics View 65
- Queue Rotation Interface View 65
- ATM Client Application 66
- ATM Link Modeling Options 67
- EnvMon Application 68
- Temperature Status 69
- Voltage Status 69
- Discovery Application 70
- Bit Status Description 71
- Mode Description 72
- Cisco Interface Application 73
- RS232 Asynchronous Port Table 74
- Line Configuration View 74
- Monitor 77
- Cisco Frame Relay Application 78
- DLCI Connection View 79
- Frame Relay Circuit Table 79
- Management Table 80
- Frame Relay Error Table 81
- Cisco Frame Relay LMI Table 82
- Protocol Power Value 83
- Cisco Frame Relay Map Table 84
- Performance Views 86
- Performance View 87
- Port Performance View 87
- Button Opens the 88
- Configuration View 89
- Discover/Reconfigure Control 90
- IF Address Translation 90
- Buffer Management 90
- Network/Host Config 90
- Redundancy and Model 91
- Reconfiguration Options View 91
- Cisco Buffer Management View 92
- Buffer Elements 93
- Buffer Management Buttons 93
- Field Description 94
- Field Description 94
- Config button 96
- Cisco Config-Copy Table View 98
- Model Information View 101
- Index Index 103
Verwandte Produkte und Handbücher für Faxgeräte Cisco MC3810
Faxgeräte Cisco BTS 10200 Installationsanleitung
(60 Seiten)
(60 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.719 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern