Cisco 2525 - 2525 TR Router Handbuch

interface Interface Commands IR-109interfaceUse the interface global configuration command to configure an interface type and enter interfaceconfiguratio

interface vg-anylanIR-118Cisco IOS Interface Command Referenceinterface vg-anylanUse the interface vg-anylan global configuration command to specify th

international bit Interface Commands IR-119international bitTo set the E3 international bit in the G.751 frame used by the PA-E3 port adapter, use the

invert dataIR-120Cisco IOS Interface Command Referenceinvert dataTo invert the data stream, use the invert data interface configuration command. This c

invert data Interface Commands IR-121Related CommandsYou can use the master indexes or search online to find documentation of related commands.t1 linec

invert rxclockIR-122Cisco IOS Interface Command Referenceinvert rxclockTo configure UIO serial port 0 or 1 on the Cisco MC3810 when the cable connected

invert-transmit-clock Interface Commands IR-123invert-transmit-clockThe invert txclock command replaces this command. Refer to the description of inve

invert txclockIR-124Cisco IOS Interface Command Referenceinvert txclockUse the invert txclock interface configuration command to invert the transmit cl

keepalive Interface Commands IR-125keepaliveTo set the keepalive timer for a specific interface, use the keepalive interface configurationcommand. To tu

lex burned-in-addressIR-126Cisco IOS Interface Command Referencelex burned-in-addressTo set the burned-in MAC address for a LAN Extender interface, us

lex input-address-list Interface Commands IR-127lex input-address-listTo assign an access list that filters on MAC addresses, use the lex input-address

interfaceIR-110Cisco IOS Interface Command ReferenceDefaultNo interface types are configured.Command ModeGlobal configurationUsage GuidelinesThis comman

lex input-type-listIR-128Cisco IOS Interface Command Referencelex input-type-listUse the lex input-type-list interface configuration command to assign

lex priority-group Interface Commands IR-129lex priority-groupUse the lex priority-group interface configuration command to activate priority output qu

lex retry-countIR-130Cisco IOS Interface Command Referencelex retry-countUse the lex retry-count interface configuration command to define the number of

lex timeout Interface Commands IR-131lex timeoutUse the lex timeout interface configuration command to define the amount of time to wait for aresponse f

linecodeIR-132Cisco IOS Interface Command ReferencelinecodeUse the linecode controller configuration command to select the line-code type for T1 or E1

link-test Interface Commands IR-133link-testTo reenable the link-test function on a port on an Ethernet hub of a Cisco 2505 or Cisco 2507, usethe link

local-lnmIR-134Cisco IOS Interface Command Referencelocal-lnmTo enable Lanoptics Hub Networking Management of a PCbus Token Ring interface, use theloc

loopback (interface) Interface Commands IR-135loopback (interface)To diagnose equipment malfunctions between interface and device, use the loopback in

loopback (interface)IR-136Cisco IOS Interface Command ReferenceRelated CommandsYou can use the master indexes or search online to find documentation of

loopback (E3/T3 interface) Interface Commands IR-137loopback (E3/T3 interface)To loop the serial interface on a PA-E3 or a PA-T3 port adapter, use the

interface Interface Commands IR-111ExamplesThe following example configures serial interface 0 with PPP encapsulation:interface serial 0encapsulation p

loopback (T1 interface)IR-138Cisco IOS Interface Command Referenceloopback (T1 interface)To loop individual T1 channels on the Channelized T3 Interfac

loopback (T1 interface) Interface Commands IR-139To better diagnose T1 provisioning problems, you can place the the remote CSU or remoteSmartJack into

loopback (T1 interface)IR-140Cisco IOS Interface Command ReferenceRelated CommandsYou can use the master indexes or search online to find documentation

loopback (T3 controller) Interface Commands IR-141loopback (T3 controller)To loop the entire T3 (all 28 T1 channels) on the Channelized T3 Interface P

loopback appliqueIR-142Cisco IOS Interface Command Referenceloopback appliqueTo configure an internal loop on the HSSI applique, use the loopback inter

loopback dte Interface Commands IR-143loopback dteTo loop packets back to the DTE from the CSU/DSU, when the device supports this feature, use theloop

loopback lineIR-144Cisco IOS Interface Command Referenceloopback lineUse the loopback line interface configuration command, to loop packets completely

loopback line Interface Commands IR-145ExamplesThe following example configures the loopback test on the DCE device:interface serial 1loopback lineThe

loopback remote (interface)IR-146Cisco IOS Interface Command Referenceloopback remote (interface)To loop packets through a CSU/DSU, over a DS-3 link o

loopback remote (interface) Interface Commands IR-147Syntax Description for 2- and 4-Wire, 56/64-kbps CSU/DSU ModulesDefaultDisabledCommand ModeInterf

interfaceIR-112Cisco IOS Interface Command ReferenceRelated CommandsYou can use the master indexes or search online to find documentation of related co

loopback remote (interface)IR-148Cisco IOS Interface Command ReferenceFor the 2- and 4-wire, 56/64-kbps CSU/DSU module, an active connection is requir

interface dialer Interface Commands IR-113interface dialerTo designate a dialer rotary group leader, use the interface dialer global configuration comm

interface fastethernetIR-114Cisco IOS Interface Command Referenceinterface fastethernetTo select a particular Fast Ethernet interface for configuration

interface group-async Interface Commands IR-115interface group-asyncTo create a group interface that will serve as master, to which asynchronous inter

interface port-channelIR-116Cisco IOS Interface Command Referenceinterface port-channelTo specify a Fast EtherChannel and enter interface configuration

interface port-channel Interface Commands IR-117Note If you do not assign a static MAC address on the port-channel interface, the Cisco IOSsoftware au