Cisco AIR-CAP1702I-EK910 Spezifikationen

GETTING STARTED GUIDE Cisco Aironet 1700 Series Access Points1 About this Guide2 Introduction to the Access Point3 Safety Instructions4 Unpacking5 Co

10 Note You cannot edit or query any access point using the controller CLI if the name of the access point contains a space.Note Make sure that the co

11 • Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a desktop.Note You can mount the access point above

12 Pre-Installation Configuration SetupThe pre-installation configuration setup is shown in Figure 3.Figure 3 Pre-Installation Configuration Setup To

13 e. CAPWAP UDP ports must not be blocked in the network.f. The access point must be able to find the IP address of the controller. This can be accom

14 Step 5 If your access point does not indicate normal operation, turn it off and repeat the pre-installation configuration.Note When you are install

15 c. (Only for APs in Unified configuration) If the LED blinks sequentially for more than 5 minutes, the access point is unable to find its primary,

16 Using DHCP Option 43You can use DHCP Option 43 to provide a list of controller IP addresses to the access points, enabling them to find and join a

17 Operating status Blinking amber Software upgrade in progressCycling through green, red, and amberDiscovery/join process in progressRapidly cycling

18 Troubleshooting the Access Point Join ProcessNote The controller must be running Cisco IOS Software Release 8.0.x.x or later to support 1700 series

19 • An existing access point running software release 8.0.x.x or later has been reset after clearing the configuration.If any of these conditions are

2 OL-32413-01Last Updated: December 12, 2014

20 11 Declarations of Conformity and Regulatory InformationThis section provides declarations of conformity and regulatory information for the Cisco

21 This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

22 VCCI Statement for JapanWarningThis is a Class B product based on the standard of the Voluntary Control Council for Interference from Information T

23 Guidelines for Operating Cisco Aironet Access Points in JapanThis section provides guidelines for avoiding interference when operating Cisco Airone

24 Statement 371—Power Cable and AC AdapterEnglish TranslationWhen installing the product, please use the provided or designated connection cables/pow

25 Cisco Aironet Access Points are certified to the requirements of RSS-210. The use of this device in a system operating either partially or complete

26 Les utilisateurs êtes avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la p

27 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC

28 The following standards were applied:EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1Health & Safety—EN60950-1: 2005; EN 50385: 2002Radio—EN 300 3

29 This device also conforms to the EMC requirements of the Medical Devices Directive 93/42/EEC.Note This equipment is intended to be used in all EU a

3 1 About this GuideThis Guide provides instructions on how to install and configure your Cisco Aironet 1700 Series Access Point. This guide also pro

30 As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a lo

31 This Device Meets the Industry Canada Guidelines for Exposure to Radio WavesThe 1700 series device includes a radio transmitter and receiver. It is

32 Santé Canada affirme que la littérature scientifique actuelle n'indique pas qu'il faille prendre des précautions particulières lors de l&

33 Chinese Translation

English TranslationAdministrative Rules for Low-power Radio-Frequency DevicesArticle 12For those low-power radio-frequency devices that have already r

35 English TranslationLow-power Radio-frequency Devices Technical SpecificationsOperation of Cisco Aironet Access Points in BrazilThis section contain

36 Figure 4 Brazil Regulatory InformationPortuguese TranslationEste equipamento opera em caráter secundário, isto é, não tem direito a proteção contra

37 12 Configuring DHCP Option 43 and DHCP Option 60This section contains a DHCP Option 43 configuration example on a Windows 2003 Enterprise DHCP ser

38 <Default router> is the IP address of the default router, such as 10.0.0.1<DNS Server> is the IP address of the DNS server, such as 10.

4 –Throughput, forwarding, and filtering performance scaled to meet 2 spatial streams, 1.3-Gbps data-rates• 64 MB flash size• 802.3af/802.3at compatib

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list ofCis

5 WarningInstallation of the equipment must comply with local and national electrical codes. Statement 1074WarningThis product relies on the building’

6 4 UnpackingTo unpack the access point, follow these steps:Step 1 Unpack and remove the access point and the accessory kit from the shipping box.Ste

7 Countries Supported Click this URL to browse to a list of countries and regulatory domains supported by the 1700:www.cisco.com/go/aironet/compliance

8 Figure 2 Access Point Ports and Connections (bottom)-AIR1702I Model1Kensington lock slot4Auxiliary Ethernet Port2DC Power connection port5RS232 Cons

9 Note The Auxiliary Ethernet port is disabled. Do not connect this port to a PoE switch. Connecting the primary and auxiliary ports to a PoE switch w